Windows NT
Microsoft® Windows® 95 Adapter Help

This Help file was compiled by the Product Support Services (PSS) group at Microsoft and will assist you in the setup of your Adapter cards for Windows 95.  Below you will find some of the most commonly used Adapters listed by function and manufacturer.  Wherever possible, the cards default settings have been indicated in italic text.  Please refer to the appropriate manufacturer and card for specific instructions.

Network Adapter Cards

3Com	DEC	Intel	Novell	Racore
Amplicard	DCA	Madge	Olicom	SMC
Artisoft	Everex	NCR	Proteon	Thomas Conrad
Cabletron	HP	NetWorth	Pure Data	Toshiba
Compaq	IBM	Network Peripherals	Racal	UngermanBass
				WD(SMC)
SCSI Adapters

Adaptec	DPT	IBM	UltraStor
Always	DTC	NCR
BusLogic	Future Domain	Trantor
Sound Cards

Creative Labs	Media Vision	Microsoft

Terminology

Base Address	DMA	SCSI	SCSI Types
COAX Cable	IRQ	SCSI Connectors	Serial Connectors
NOTE:

This Help file is not intended to be a replacement for the documentation that was provided with your Adapter card(s). It is provided as a convenience, in the hopes that it will help you get your Adapter card(s) configured more quickly. This Help file provides IRQ,  I/O Base, RAM Base Address and other settings as a convienence. For information not covered in this Help file, please consult the documentation that was supplied with your Adapter card.

The products included here are manufactured by vendors independent of Microsoft; we make no warranty, implied or otherwise, regarding these products performance or reliability.


Network Peripherals Cards
Network Peripherals

Windows NT Adapter help currently includes the following Network Peripherals network adapters

Network Peripherals NP-EISA/S

Network Peripherals NP-MCA/S


Network Peripherals NP-EISA/S Card
Network Peripherals NP-EISA/S

This is the Network Peripherals NP-EISA/S Network Adapter card shown. The Installation/Diagnostic Program is a menu based program that allows the installer to configure, install and test a network interface. To run it type:

NPINST <RETURN>.

I/O Base Address

Switch S1

1	2	3

160	ON	OFF	ON

180	ON	OFF	OFF

260	OFF	ON	ON

280	OFF	ON	OFF

360	OFF	OFF	ON

380	OFF	OFF	OFF

Port Type Configuration

Jumper Block JP11

1	2

'A' Type	OFF	OFF

'S' Type	OFF	ON

'M' Type	ON	OFF

'B' Type	ON	ON

Cabling for this Adapter

FDDI Connector


Network Peripherals NP-MCA/S Card
Network Peripherals NP-MCA/S

This is the Network Peripherals NP-MCA/S Network Adapter card shown.  The manual and the README.1ST file on the installation diskette contain information about installing this adapter in your system. Run NPINST to determine the available Hardware Interrupts (IRQs) in the system. IRQs can be set by using the Reference Diskette that came with your MicroChannel Computer.

Cabling for this Adapter

FDDI Connector


Cabletron Cards
Cabletron

Windows '95 Adapter help currently includes the following Cabletron network adapters

Cabletron E2100

Cabletron E1100


Cabletron E1100

This is the Cabletron E1100 Network Adapter card shown.  Listed below are the possible Base I/O Address jumper configurations. IRQ is configured by software.:


Cabletron E2100

This is the Cabletron E2100 Network Adapter card shown.  Listed below are the possible Base I/O Address jumper configurations. IRQ is configured by software.:

Base I/O Address

BASE I/O JUMPER BLOCK JP1

1	2

220h	ON	ON

280h	ON	OFF

300h	OFF	ON

380h	OFF	OFF

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector

Thin Ethernet via BNC Connector


3Com Cards
3COM

Windows 95 Adapter help currently includes the following 3Com network cards:

3Com Etherlink 16 (3C507)

3Com Etherlink II (8 or 16-Bit 3C503) 2227-xx

3Com Etherlink II (8-or 16-Bit 3C503) 7920-xxxx

3Com Etherlink/MC (3C523)

3Com Etherlink III (3C509)

3Com Etherlink III - TP (3C509)

3Com Etherlink III - COMBO (3C509)

3Com Tokenlink (3C603)3Com Etherlink Plus (3C505-B)


3Com Etherlink 16 Card
3Com Etherlink 16 (3C507)

This Network Adapter card can be configured using the software supplied by the manufacturer. Please consult the documentation that came with your Network Adapter or contact the manufacturer of the Network Adapter for further information.

Interrupt Request Line (IRQ)

Default - IRQ3

Base I/O Address

Default - 300h

Base Memory Address

Default - D000h

Cabling for this Adapter

Thick Ethernet via AUI Connector

Thin Ethernet via BNC Connector


3Com Etherlink II (8 or 16-Bit) 2227-xx Card
3Com Etherlink II (8 or 16-Bit 3C503) 2227-xx

This is the 3Com Etherlink II (8 or 16-Bit 3C503) 2227-xx Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

SOFTWARE CONFIGURABLE

Default - IRQ3

Base I/O Address

BASE I/O JUMPER BLOCK

J1	J2	J3	J4	J5	J6	J7	J8

250h	OFF	OFF	OFF	ON	OFF	OFF	OFF	OFF

280h	OFF	OFF	ON	OFF	OFF	OFF	OFF	OFF

2A0h	OFF	ON	OFF	OFF	OFF	OFF	OFF	OFF

2E0h	ON	OFF	OFF	OFF	OFF	OFF	OFF	OFF

300h	OFF	OFF	OFF	OFF	OFF	OFF	OFF	ON

310h	OFF	OFF	OFF	OFF	OFF	OFF	ON	OFF

330h	OFF	OFF	OFF	OFF	OFF	ON	OFF	OFF

350h	OFF	OFF	OFF	OFF	ON	OFF	OFF	OFF

Base Memory Address

Base Memory Address JUMPER BLOCK

J1	J2	J3	J4	J5

DISABLED	OFF	OFF	OFF	OFF	ON

C800h	ON	OFF	OFF	OFF	OFF

CC00h	OFF	ON	OFF	OFF	OFF

D800h	OFF	OFF	ON	OFF	OFF

DC00h	OFF	OFF	OFF	ON	OFF

Cabling for this Adapter

Thick Ethernet via AUI Connector

Thin Ethernet via BNC Connector


3Com Etherlink II (8 or 16-Bit) 7920-xxxx Card
3Com Etherlink II (8 or 16-Bit 3C503) 7920-xxxx

This is the 3Com Etherlink II (8 or 16-Bit) 7920-xxxx Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

SOFTWARE CONFIGURABLE

Default - IRQ3

Base I/O Address

BASE I/O JUMPER BLOCK

J1	J2	J3	J4	J5	J6	J7	J8

250h	OFF	OFF	OFF	OFF	ON	OFF	OFF	OFF

280h	OFF	OFF	OFF	OFF	OFF	ON	OFF	OFF

2A0h	OFF	OFF	OFF	OFF	OFF	OFF	ON	OFF

2E0h	OFF	OFF	OFF	OFF	OFF	OFF	OFF	ON

300h	ON	OFF	OFF	OFF	OFF	OFF	OFF	OFF

310h	OFF	ON	OFF	OFF	OFF	OFF	OFF	OFF

330h	OFF	OFF	ON	OFF	OFF	OFF	OFF	OFF

350h	OFF	OFF	OFF	ON	OFF	OFF	OFF	OFF

Base Memory Address

Base Memory Address JUMPER BLOCK

J1	J2	J3	J4	J5

DISABLED	ON	OFF	OFF	OFF	OFF

C800h	OFF	ON	OFF	OFF	OFF

CC00h	OFF	OFF	ON	OFF	OFF

D800h	OFF	OFF	OFF	ON	OFF

DC00h	OFF	OFF	OFF	OFF	ON

Cabling for this Adapter

Thick Ethernet via AUI Connector

Thin Ethernet via BNC Connector


3Com Etherlink/MC Card
3Com Etherlink/MC (3C523)

This Network Adapter card is configured using the 'Reference Disk' provided with your Micro-Channel System.  For further information consult the documentation provided with the Network Adapter or contact your vendor.

Interrupt Request Line (IRQ)

Default - IRQ3

Base I/O Address

Default - 300h


3Com Etherlink Plus Card
3Com Etherlink Plus (3C505-B)

This is the 3Com Etherlink Plus Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ

JP1	JP2

J9	J10	J11	J12	J13	J1	J2	J3	J4	J5	J6

IRQ3	OFF	OFF	OFF	OFF	OFF	ON	OFF	OFF	OFF	OFF	OFF

IRQ4	OFF	OFF	OFF	OFF	OFF	OFF	ON	OFF	OFF	OFF	OFF

IRQ5	OFF	OFF	OFF	OFF	OFF	OFF	OFF	ON	OFF	OFF	OFF

IRQ6	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF	ON	OFF	OFF

IRQ7	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF	ON	OFF

IRQ9	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF	ON

IRQ10	OFF	OFF	OFF	OFF	ON	OFF	OFF	OFF	OFF	OFF	OFF

IRQ11	OFF	OFF	OFF	ON	OFF	OFF	OFF	OFF	OFF	OFF	OFF

IRQ12	OFF	OFF	ON	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF

IRQ14	ON	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF

IRQ15	OFF	ON	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF

Base I/O Address

JP3

J4	J5	J6	J7	J8	J9

300h	2-3	2-3	2-3	2-3	1-2	1-2

310h	1-2	2-3	2-3	2-3	1-2	1-2

330h	1-2	1-2	2-3	2-3	1-2	1-2

350h	1-2	2-3	1-2	2-3	1-2	1-2

Base Memory Address

NOT USED


3Com Tokenlink Card
3Com Tokenlink (3C603)

This is the 3Com Tokenlink Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

IRQ JUMPER BLOCK

J1	J2	J3	J4	J5	J6	J7	J8

IRQ2	ON	OFF	OFF	OFF	OFF	OFF	OFF	OFF

IRQ3	OFF	ON	OFF	OFF	OFF	OFF	OFF	OFF

IRQ4	OFF	OFF	ON	OFF	OFF	OFF	OFF	OFF

IRQ5	OFF	OFF	OFF	ON	OFF	OFF	OFF	OFF

IRQ10	OFF	OFF	OFF	OFF	ON	OFF	OFF	OFF

IRQ11	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF

IRQ12	OFF	OFF	OFF	OFF	OFF	OFF	ON	OFF

IRQ14	OFF	OFF	OFF	OFF	OFF	OFF	OFF	ON

Base I/O Address

BASE I/O JUMPER BLOCK

J1	J2	J3	J4

300h	ON	OFF	OFF	OFF

310h	OFF	ON	OFF	OFF

330h	OFF	OFF	ON	OFF

350h	OFF	OFF	OFF	ON

Base Memory Address

NOT USED


3Com 3C509 Card
3Com Etherlink III (3C509)

This Network Adapter card can be configured using the software supplied by the manufacturer. Please consult the documentation that came with your Network Adapter or contact the manufacturer of the Network Adapter for further information.

Interrupt Request Line (IRQ)

Default - IRQ10

Base I/O Address

Default - 300h

Cabling for this Adapter

Thick Ethernet via AUI Connector

Thin Ethernet via BNC Connector


3Com 3C509-TP Card
3Com Etherlink III - TP (3C509)

This Network Adapter card can be configured using the software supplied by the manufacturer. Please consult the documentation that came with your Network Adapter or contact the manufacturer of the Network Adapter for further information.

Interrupt Request Line (IRQ)

Default - IRQ10

Base I/O Address

Default - 300h

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector

Thin Ethernet via BNC Connector


3Com 3C509-COMBO Card
3Com Etherlink III COMBO (3C509)

This Network Adapter card can be configured using the software supplied by the manufacturer. Please consult the documentation that came with your Network Adapter or contact the manufacturer of the Network Adapter for further information.

Interrupt Request Line (IRQ)

Default - IRQ10

Base I/O Address

Default - 300H

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector

Thick Ethernet via AUI Connector

Thin Ethernet via BNC Connector


Amplicard Cards
Amplicard

Windows 95 Adapter help currently includes the following Amplicard network cards:

Amplicard AC 210/XT

Amplicard AC 210/AT


Amplicard AC 210/XT Card
Amplicard AC 210/XT

This is the Amplicard AC 210/XT Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

WJ4

IRQ2	7-8

IRQ3	5-6

IRQ4	3-4

IRQ5	1-2

Base I/O Address

WJ2	WJ25

300h	1-2	1-2

320h	2-3	1-2

340h	1-2	2-3

360h	2-3	2-3

Base Memory Address

SOFTWARE CONFIGURABLE

Default - D000h

Cabling for this Adapter

Thick Ethernet via AUI Connector

Thin Ethernet via BNC Connector


Amplicard AC 210/AT

This is the Amplicard AC 210/AT Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

WJ4

IRQ2	7-8

IRQ3	5-6

IRQ4	3-4

IRQ5	1-2

Base I/O Address

WJ2	WJ24

300h	1-2	1-2

320h	1-2	2-3

340h	2-3	2-3

360h	2-3	1-2

Base Memory Address

SOFTWARE CONFIGURABLE

Default - D000h

Cabling for this Adapter

Thick Ethernet via AUI Connector

Thin Ethernet via BNC Connector


Artisoft Cards
Artisoft

Windows 95 Adapter help currently includes the following Artisoft network cards:

Artisoft AE-1/T (Twisted Pair)

Artisoft AE-2/T (Twisted Pair)

Artisoft AE-2/C (Thinnet/Coax)

Artisoft AE-2 (MCA) or AE-3 (MCA)

Artisoft AE-3


Artisoft AE-1
Artisoft AE-1/T

This is the Artisoft AE-1/T Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

W2

J2	J3	J4	J5	J6	J7	J10	J15

IRQ2	ON	OFF	OFF	OFF	OFF	OFF	OFF	OFF

IRQ3	OFF	ON	OFF	OFF	OFF	OFF	OFF	OFF

IRQ4	OFF	OFF	ON	OFF	OFF	OFF	OFF	OFF

IRQ5	OFF	OFF	OFF	ON	OFF	OFF	OFF	OFF

IRQ6	OFF	OFF	OFF	OFF	ON	OFF	OFF	OFF

IRQ7	OFF	OFF	OFF	OFF	OFF	ON	OFF	OFF

IRQ10	OFF	OFF	OFF	OFF	OFF	OFF	ON	OFF

IRQ15	OFF	OFF	OFF	OFF	OFF	OFF	OFF	ON

Base I/O Address

W1

A	B	C	D

300h	ON	ON	OFF	OFF

320h	OFF	ON	OFF	ON

340h	ON	OFF	ON	OFF

360h	OFF	OFF	ON	ON

Base Memory Address

NOT USED

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector


Artisoft AE-2 (Twisted Pair)
Artisoft AE-2/T (Twisted Pair)

This is the Artisoft AE-2 Card (Twisted Pair) shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

W1

J2	J3	J4	J5	J6	J7	J10	J15

IRQ2	ON	OFF	OFF	OFF	OFF	OFF	OFF	OFF

IRQ3	OFF	ON	OFF	OFF	OFF	OFF	OFF	OFF

IRQ4	OFF	OFF	ON	OFF	OFF	OFF	OFF	OFF

IRQ5	OFF	OFF	OFF	ON	OFF	OFF	OFF	OFF

IRQ6	OFF	OFF	OFF	OFF	ON	OFF	OFF	OFF

IRQ7	OFF	OFF	OFF	OFF	OFF	ON	OFF	OFF

IRQ10	OFF	OFF	OFF	OFF	OFF	OFF	ON	OFF

IRQ15	OFF	OFF	OFF	OFF	OFF	OFF	OFF	ON

Base I/O Address

W4

A	B	C	D

300h	ON	ON	OFF	OFF

320h	ON	OFF	ON	OFF

340h	OFF	ON	OFF	ON

360h	OFF	OFF	ON	ON

Base Memory Address

NOT USED

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector

Thick Ethernet via AUI Connector


Artisoft AE-2 (Thinnet)
Artisoft AE-2/C (Thinnet)

This is the Artisoft AE-2/C Card (Thinnet) shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

W1

J2	J3	J4	J5	J6	J7	J10	J15

IRQ2	ON	OFF	OFF	OFF	OFF	OFF	OFF	OFF

IRQ3	OFF	ON	OFF	OFF	OFF	OFF	OFF	OFF

IRQ4	OFF	OFF	ON	OFF	OFF	OFF	OFF	OFF

IRQ5	OFF	OFF	OFF	ON	OFF	OFF	OFF	OFF

IRQ6	OFF	OFF	OFF	OFF	ON	OFF	OFF	OFF

IRQ7	OFF	OFF	OFF	OFF	OFF	ON	OFF	OFF

IRQ10	OFF	OFF	OFF	OFF	OFF	OFF	ON	OFF

IRQ15	OFF	OFF	OFF	OFF	OFF	OFF	OFF	ON

Base I/O Address

W4

A	B	C	D

300h	ON	ON	OFF	OFF

320h	ON	OFF	ON	OFF

340h	OFF	ON	OFF	ON

360h	OFF	OFF	ON	ON

Base Memory Address

NOT USED

Cabling for this Adapter

Thick Ethernet via AUI Connector

Thin Ethernet via BNC Connector


Artisoft AE-2 (MCA) or AE-3 (MCA)

This Network Adapter card is configured using the 'Reference Disk' provided with your Micro-Channel System.  For further information consult the documentation provided with the Network Adapter or contact your vendor.

Cabling for this Adapter

Thick Ethernet via AUI Connector

Thin Ethernet via BNC Connector


Artisoft AE-3

This is the Artisoft AE-3 Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

W1

J2	J3	J4	J5	J6	J7	J10	J15

IRQ2	ON	OFF	OFF	OFF	OFF	OFF	OFF	OFF

IRQ3	OFF	ON	OFF	OFF	OFF	OFF	OFF	OFF

IRQ4	OFF	OFF	ON	OFF	OFF	OFF	OFF	OFF

IRQ5	OFF	OFF	OFF	ON	OFF	OFF	OFF	OFF

IRQ6	OFF	OFF	OFF	OFF	ON	OFF	OFF	OFF

IRQ7	OFF	OFF	OFF	OFF	OFF	ON	OFF	OFF

IRQ10	OFF	OFF	OFF	OFF	OFF	OFF	ON	OFF

IRQ15	OFF	OFF	OFF	OFF	OFF	OFF	OFF	ON

Base I/O Address

W4

A	B	C	D

300h	ON	ON	OFF	OFF

320h	ON	OFF	ON	OFF

340h	OFF	ON	OFF	ON

360h	OFF	OFF	ON	ON

Base Memory Address

NOT USED

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector

Thick Ethernet via AUI Connector

Thin Ethernet via BNC Connector


Compaq Cards
Compaq

Windows 95 Adapter help currently includes the following Compaq network cards:

Compaq 32-Bit Dualspeed Token Ring


Compaq 32-Bit Dualspeed Token Ring

This can be configured using the ECU (EISA Configuration Utility) that ships with most EISA systems. For question about use of the ECU, please consult the documentation that came with your system or contact the manufacturer of the system.

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector

Shielded Twisted Pair (IBM Type 1) via DB-9 Connector


DCA Cards
DCA

Windows 95 Adapter help currently includes the following DCA network cards:

DCA 10 Mb MCA

DCA 10 Mb Twisted Pair


DCA 10 Mb MCA

This Network Adapter card is configured using the 'Reference Disk' provided with your Micro-Channel System.  For further information consult the documentation provided with the Network Adapter or contact your vendor.

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector


DCA 10 Mb Twisted Pair

This is the DCA 10 Mb Twisted Pair Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

SOFTWARE CONFIGURABLE

Default - IRQ3

Base I/O Address

SW1

S1	S2	S3	S4

300h	OFF	OFF	OFF	OFF

310h	ON	OFF	OFF	OFF

330h	OFF	ON	OFF	OFF

350h	ON	ON	OFF	OFF

Base Memory Address

SOFTWARE CONFIGURABLE

Default - D000h

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector


DEC Cards
DEC

Windows 95 Adapter help currently includes the following DEC network cards:

DEC DEPCA

DEC EtherWorks LC

DEC EtherWorks LC/TP

DEC EtherWorks Turbo

DEC EtherWorks Turbo/TP

DEC EtherWorks Turbo/TP_BNC

DEC EtherWorks MC

DEC EtherWorks MC/TP_BNC

DEC EtherWorks EISA/TP_BNC


DEC Etherworks EISA /TP_BNC

This is the DEC Etherworks EISA/TP_BNC Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Setup Choice for Windows NT 3.5

DEC EtherWORKS DEPCA

AUI/TP Jumper J1

1	2	3

BNC	OFF	ON	ON

TP	ON	ON	OFF

Note - 1, 2, and 3 represent rows of pins that the block jumper fits on (only two of the rows at a time).

Cabling for this Adapter

Thin Ethernet via BNC Connector

Unshielded Twisted Pair via RJ-45 Connector


DEC DEPCA

This is the DEC DEPCA Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

W1	W2	W3	W4	W5

IRQ2	2-3	OFF	OFF	OFF	OFF

IRQ3	OFF	2-3	OFF	OFF	OFF

IRQ4	OFF	OFF	2-3	OFF	OFF

IRQ5	OFF	OFF	OFF	2-3	OFF

IRQ7	OFF	OFF	OFF	OFF	2-3

Base I/O Address

W6

200h	OFF

300h	ON

Base Memory Address - 64K BUFFER (Rev. E Only)

W7	W8

D000h	ON	ON

E000h	OFF	ON

Base Memory Address - 32K BUFFER (Rev. E Only)

W7	W8

C800h	OFF	OFF

D800h	ON	OFF

Base Memory Address - 64K BUFFER (Rev. D Only)

W7

D000h	ON

E000h	OFF

Cabling for this Adapter

Thin Ethernet via BNC Connector


DEC Etherworks LC

This is the DEC Etherworks LC Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

S8	S9	S10	S11	S12

IRQ2	ON	OFF	OFF	OFF	OFF

IRQ3	OFF	ON	OFF	OFF	OFF

IRQ4	OFF	OFF	ON	OFF	OFF

IRQ5	OFF	OFF	OFF	ON	OFF

IRQ7	OFF	OFF	OFF	OFF	ON

Base I/O Address

S5

200h	OFF

300h	ON

Base Memory Address - 64K BUFFER

S1	S2	S3	S4

C000h	OFF	ON	ON	ON

D000h	ON	ON	ON	ON

E000h	OFF	OFF	ON	ON

Base Memory Address - 32K BUFFER

S1	S2	S3	S4

C800h	OFF	ON	OFF	ON

D800h	ON	ON	OFF	ON

E800h	OFF	OFF	OFF	ON

Cabling for this Adapter

Thick Ethernet via AUI Connector

Thin Ethernet via BNC Connector


DEC Etherworks LC/TP

This is the DEC Etherworks LC/TP Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

S8	S9	S10	S11	S12

IRQ2	ON	OFF	OFF	OFF	OFF

IRQ3	OFF	ON	OFF	OFF	OFF

IRQ4	OFF	OFF	ON	OFF	OFF

IRQ5	OFF	OFF	OFF	ON	OFF

IRQ7	OFF	OFF	OFF	OFF	ON

Base I/O Address

S5

200h	OFF

300h	ON

Base Memory Address - 64K BUFFER

S1	S2	S3	S4

C000h	OFF	ON	ON	ON

D000h	ON	ON	ON	ON

E000h	OFF	OFF	ON	ON

Base Memory Address - 32K BUFFER

S1	S2	S3	S4

C800h	OFF	ON	OFF	ON

D800h	ON	ON	OFF	ON

E800h	OFF	OFF	OFF	ON

Cabling for this Adapter

Thick Ethernet via AUI Connector

Unshielded Twisted Pair via RJ-45 Connector


DEC Etherworks MC

This Network Adapter card is configured using the 'Reference Disk' provided with your Micro-Channel System.  For further information consult the documentation provided with the Network Adapter or contact your vendor.

Cabling for this Adapter

Thick Ethernet via AUI Connector

Thin Ethernet via BNC Connector


DEC Etherworks MC/TP_BNC

This Network Adapter card is configured using the 'Reference Disk' provided with your Micro-Channel System.  For further information consult the documentation provided with the Network Adapter or contact your vendor.

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector

Thick Ethernet via AUI Connector


DEC Etherworks Turbo

This is the DEC Etherworks Turbo Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

S8	S9	S10	S11	S12

IRQ5	ON	OFF	OFF	OFF	OFF

IRQ9	OFF	ON	OFF	OFF	OFF

IRQ10	OFF	OFF	ON	OFF	OFF

IRQ11	OFF	OFF	OFF	ON	OFF

IRQ15	OFF	OFF	OFF	OFF	ON

Base I/O Address

S5

200h	OFF

300h	ON

Base Memory Address - 64K BUFFER

S1	S2	S3	S4

C000h	ON	ON	ON	ON

D000h	ON	OFF	ON	ON

E000h	OFF	ON	ON	ON

Base Memory Address - 32K BUFFER

S1	S2	S3	S4

C800h	ON	ON	OFF	OFF

D800h	ON	OFF	OFF	OFF

E800h	OFF	ON	OFF	OFF

Cabling for this Adapter

Thick Ethernet via AUI Connector

Thin Ethernet via BNC Connector


DEC Etherworks Turbo/TP

This is the DEC Etherworks Turbo/TP Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

S8	S9	S10	S11	S12

IRQ5	ON	OFF	OFF	OFF	OFF

IRQ9	OFF	ON	OFF	OFF	OFF

IRQ10	OFF	OFF	ON	OFF	OFF

IRQ11	OFF	OFF	OFF	ON	OFF

IRQ15	OFF	OFF	OFF	OFF	ON

Base I/O Address

S5

200h	OFF

300h	ON

Base Memory Address - 64K BUFFER

S1	S2	S3	S4

C000h	ON	ON	ON	ON

D000h	ON	OFF	ON	ON

E000h	OFF	ON	ON	ON

Base Memory Address - 32K BUFFER

S1	S2	S3	S4

C800h	ON	ON	OFF	OFF

D800h	ON	OFF	OFF	OFF

E800h	OFF	ON	OFF	OFF

AUI/TP Jumper

1	2	3

AUI	ON	ON	OFF

TP	OFF	ON	ON

Note - 1, 2, and 3 represent rows of pins that the block jumper fits on (only two of the rows at a time).

Cabling for this Adapter

Thick Ethernet via AUI Connector

Unshielded Twisted Pair via RJ-45 Connector


DEC Etherworks Turbo/TP_BNC

This is the DEC Etherworks Turbo/TP_BNC Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

S8	S9	S10	S11	S12

IRQ5	ON	OFF	OFF	OFF	OFF

IRQ9	OFF	ON	OFF	OFF	OFF

IRQ10	OFF	OFF	ON	OFF	OFF

IRQ11	OFF	OFF	OFF	ON	OFF

IRQ15	OFF	OFF	OFF	OFF	ON

Base I/O Address

S5

200h	OFF

300h	ON

Base Memory Address - 64K BUFFER

S1	S2	S3	S4

C000h	ON	ON	ON	ON

D000h	ON	OFF	ON	ON

E000h	OFF	ON	ON	ON

Base Memory Address - 32K BUFFER

S1	S2	S3	S4

C800h	ON	ON	OFF	OFF

D800h	ON	OFF	OFF	OFF

E800h	OFF	ON	OFF	OFF

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector

Thin Ethernet via BNC Connector


Everex Cards
Everex

Windows 95 Adapter help currently includes the following Everex network cards:

Everex Speedlink /PC16


Everex Speedlink /PC16

This is the Everex Speedlink /PC16 Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

SOFTWARE CONFIGURABLE

Interrupt Request Line (IRQ)

Default - IRQ4

I/O BASE ADDRESS

SW1

S1	S2	S3	S4	S5	S6	S7	S8

340h	ON	ON	ON	ON	OFF	ON	OFF	OFF

348h	ON	OFF	ON	ON	OFF	ON	OFF	OFF

350h	ON	ON	OFF	ON	OFF	ON	OFF	OFF

358h	ON	OFF	OFF	ON	OFF	ON	OFF	OFF

360h	ON	ON	ON	OFF	OFF	ON	OFF	OFF

368h	ON	OFF	ON	OFF	OFF	ON	OFF	OFF

370h	ON	ON	OFF	OFF	OFF	ON	OFF	OFF

378h	ON	OFF	OFF	OFF	OFF	ON	OFF	OFF

390h	ON	ON	OFF	ON	ON	OFF	OFF	OFF

398h	ON	OFF	OFF	ON	ON	OFF	OFF	OFF

Base Memory Address

NOT USED

Cabling for this Adapter

Thick Ethernet via AUI Connector

Thin Ethernet via BNC Connector


HP Cards
HP

Windows 95 Adapter help currently includes the following HP network cards:

HP MC LAN Adapter/16 TP (HP27246A)

HP PC LAN Adapter/8 TL (HP27250A)

HP PC LAN Adapter/8 TP (HP27245A)

HP PC LAN Adapter/16 TP HP(27247A)

HP PC LAN Adapter/16 TL Plus (HP27252A)

HP PC LAN Adapter/16 TP Plus (HP27247B)

HP StarLAN Adapter

HP StarLAN MCA Adapter


HP MC LAN Adapter/16 TP

This Network Adapter card is configured using the 'Reference Disk' provided with your Micro-Channel System.  For further information consult the documentation provided with the Network Adapter or contact your vendor.

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector


HP PC LAN Adapter/8 TL

This is the HP PC LAN Adapter/8 TL Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

SOFTWARE CONFIGURABLE

Default - IRQ3

Base I/O Address

SW1

S1	S2	S3

200h	OFF	OFF	OFF

240h	OFF	OFF	ON

280h	OFF	ON	OFF

2C0h	OFF	ON	ON

300h	ON	OFF	OFF

320h	ON	OFF	ON

340h	ON	ON	OFF

Base Memory Address

NOT USED

Cabling for this Adapter

Thick Ethernet via AUI Connector

Thin Ethernet via BNC Connector


HP PC LAN Adapter/8 TP

This is the HP PC LAN Adapter/8 TP Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

SOFTWARE CONFIGURABLE

Base I/O Address

SW1

S1	S2	S3

200h	OFF	OFF	OFF

240h	OFF	OFF	ON

280h	OFF	ON	OFF

2C0h	OFF	ON	ON

300h	ON	OFF	OFF

320h	ON	OFF	ON

340h	ON	ON	OFF

Base Memory Address

NOT USED

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector


HP PC LAN Adapter/16 TP

This is the HP PC LAN Adapter/16 TP Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

SOFTWARE CONFIGURABLE

Default - IRQ3

Base I/O Address

SW1

S1	S2	S3

200h	OFF	OFF	OFF

240h	OFF	OFF	ON

280h	OFF	ON	OFF

2C0h	OFF	ON	ON

300h	ON	OFF	OFF

320h	ON	OFF	ON

340h	ON	ON	OFF

Base Memory Address

NOT USED

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector


HP PC LAN Adapter/16 TL Plus

This Network Adapter card can be configured using the software supplied by the manufacturer. Please consult the documentation that came with your Network Adapter or contact the manufacturer of the Network Adapter for further information.

Cabling for this Adapter

Thick Ethernet via AUI Connector

Thin Ethernet via BNC Connector


HP PC LAN Adapter/16 TP Plus

This Network Adapter card can be configured using the software supplied by the manufacturer. Please consult the documentation that came with your Network Adapter or contact the manufacturer of the Network Adapter for further information.

Interrupt Request Line (IRQ)

Default - IRQ3

Base I/O Address

Default - 300h

Cabling for this Adapter

Thick Ethernet via AUI Connector

Unshielded Twisted Pair via RJ-45 Connector


HP StarLAN Adapter

This is the HP StarLAN Adapter Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

SOFTWARE CONFIGURABLE

Base I/O Address

SW1

S1	S2	S3

200h	OFF	OFF	OFF

240h	OFF	OFF	ON

280h	OFF	ON	OFF

2C0h	OFF	ON	ON

300h	ON	OFF	OFF

320h	ON	OFF	ON

340h	ON	ON	OFF

Base Memory Address

NOT USED

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector


HP StarLAN MCA Adapter

This Network Adapter card is configured using the 'Reference Disk' provided with your Micro-Channel System.  For further information consult the documentation provided with the Network Adapter or contact your vendor.

Interrupt Request Line (IRQ)

Default - IRQ3

Base I/O Address

Default - 400h

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector


IBM Cards
IBM

Windows 95 Adapter help currently includes the following IBM network cards:

IBM Token Ring 16/4Mbs

IBM Token Ring 16/4Mbs (MCA)

IBM PC Network Adapter II

IBM PC Network Adapter II/A

IBM PC Network Baseband Adapter

IBM PC Network Baseband Adapter/A

IBM Token Ring

IBM Token Ring (MCA)

IBM Token Ring II


IBM PC Network Adapter II

This is the IBM PC Network Adapter II Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

W1

IRQ2	1-2

IRQ3	2-3

Base I/O Address

W4

620h	1-2

628h	2-3

Base Memory Address

W5

CC00h	1-2

DC00h	2-3

Cabling for this Adapter

Thin Ethernet via BNC Connector


IBM PC Network Adapter II/A

This Network Adapter card is configured using the 'Reference Disk' provided with your Micro-Channel System.  For further information consult the documentation provided with the Network Adapter or contact your vendor.

Cabling for this Adapter

Thin Ethernet via BNC Connector


IBM PC Network Baseband Adapter

This is the IBM PC Network Baseband Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

W1

IRQ2	1-2

IRQ3	2-3

Base I/O Address

W4

620h	1-2

628h	2-3

Base Memory Address

W5

CC00h	1-2

DC00h	2-3

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector


IBM PC Network Baseband Adapter/A

This Network Adapter card is configured using the 'Reference Disk' provided with your Micro-Channel System.  For further information consult the documentation provided with the Network Adapter or contact your vendor.

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector


IBM Token Ring

This is the IBM Token Ring Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

SW1

S7	S8

IRQ2	ON	ON

IRQ3	ON	OFF

IRQ7	OFF	OFF

Base I/O Address

SW2

S2

0A20h	OFF

0A24h	ON

Base Memory Address

NOT USED

Cabling for this Adapter

Shielded Twisted Pair via DB-9 Connector


IBM Token Ring (MCA)

This Network Adapter card is configured using the 'Reference Disk' provided with your Micro-Channel System.  For further information consult the documentation provided with the Network Adapter or contact your vendor.

Cabling for this Adapter

Shielded Twisted Pair via DB-9 Connector


IBM Token Ring II

This is the IBM Token Ring II Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

SW1

S7	S8

IRQ2	ON	ON

IRQ3	ON	OFF

IRQ7	OFF	OFF

Base I/O Address

SW1

S9

0A20h	ON

0A24h	OFF

Base Memory Address

SOFTWARE CONFIGURABLE

Cabling for this Adapter

Shielded Twisted Pair via DB-9 Connector


IBM Token Ring 4/16Mbs
IBM Token Ring 16/4Mbs

This is the IBM Token Ring 16/4Mbs Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

SW1

S7	S8

IRQ2	ON	ON

IRQ3	ON	OFF

IRQ6	OFF	ON

IRQ7	OFF	OFF

Base I/O Address

SW1

S9

0A20h	ON

0A24h	OFF

Base Memory Address

SW1

S1	S2	S3	S4	S5	S6

C000h	OFF	ON	ON	ON	ON	ON

C200h	OFF	ON	ON	ON	ON	OFF

C400h	OFF	ON	ON	ON	OFF	ON

C600h	OFF	ON	ON	ON	OFF	OFF

C800h	OFF	ON	ON	OFF	ON	ON

CA00h	OFF	ON	ON	OFF	ON	OFF

CC00h	OFF	ON	ON	OFF	OFF	ON

CE00h	OFF	ON	ON	OFF	OFF	OFF

D000h	OFF	ON	OFF	ON	ON	ON

D200h	OFF	ON	OFF	ON	ON	OFF

D400h	OFF	ON	OFF	ON	OFF	ON

D600h	OFF	ON	OFF	ON	OFF	OFF

D800h	OFF	ON	OFF	OFF	ON	ON

DA00h	OFF	ON	OFF	OFF	ON	OFF

DC00h	OFF	ON	OFF	OFF	OFF	ON

DE00h	OFF	ON	OFF	OFF	OFF	OFF

Cabling for this Adapter

Shielded Twisted Pair (IBM Type 1) via DB-9 Connector


IBM Token Ring 4/16Mbs (MCA)
IBM Token Ring 16/4Mbs (MCA)

This Network Adapter card is configured using the 'Reference Disk' provided with your Micro-Channel System.  For further information consult the documentation provided with the Network Adapter or contact your vendor.

Cabling for this Adapter

Shielded Twisted Pair (IBM Type 1) via DB-9 Connector


Intel Cards
Intel

Windows 95 Adapter help currently includes the following Intel network cards:

Intel EtherExpress 16

Intel EtherExpress 32

Intel TokenExpress EISA 16/4

Intel TokenExpress ISA 16/4

Intel TokenExpress MCA 16/4


Intel EtherExpress 16

The Intel EtherExpress 16 is software configurable and may be configured through Windows 95 Control Panel, Network section. Please consult the installation instructions that came with your Network Adapter for more information.

Cabling for this Adapter

Thick Ethernet via AUI Connector

Thin Ethernet via BNC Connector

or

Thick Ethernet via AUI Connector

Unshielded Twisted Pair via RJ-45 Connector

          on the Intel EtherExpress 16TP


Intel EtherExpress 32

This Network Adapter card can be configured using the software supplied by the manufacturer. Please consult the documentation that came with your Network Adapter or contact the manufacturer of the Network Adapter for further information.

Cabling for this Adapter

Thick Ethernet via AUI Connector

Thin Ethernet via BNC Connector


Intel TokenExpress EISA 16/4

This can be configured using the ECU (EISA Configuration Utility) that ships with most EISA systems. For question about use of the ECU, please consult the documentation that came with your system or contact the manufacturer of the system.

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector

Shielded Twisted Pair via DB-9 Connector


Intel TokenExpress ISA 16/4

This is the Intel TokenExpress ISA 16/4 Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

S7	S8

IRQ2/9	ON	ON

IRQ3	ON	OFF

IRQ10	OFF	ON

IRQ11	OFF	OFF

Base I/O Address

S9	S10

A20h/A30h	OFF	OFF

A24h/A40h	ON	OFF

A50h/A60h	OFF	ON

A54h/A70h	ON	ON

Base Memory Address

NOT USED

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector

Shielded Twisted Pair via DB-9 Connector


Intel TokenExpress MCA 16/4

This Network Adapter card is configured using the 'Reference Disk' provided with your Micro-Channel System.  For further information consult the documentation provided with the Network Adapter or contact your vendor.

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector

Shielded Twisted Pair via DB-9 Connector


Madge Cards
Madge

Windows 95 Adapter help currently includes the following Madge network cards:

Madge Networks Smart 16/4 XT RingNode

Madge Networks Smart 16/4 AT RingNode

Madge Networks Smart 16/4 EISA RingNode

Madge Networks Smart 16/4 MC RingNode


Madge Networks Smart 16/4 XT RingNode

This is the Madge Networks Smart 16/4 XT RingNode Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

SW1

S4	S5	S6	S7

IRQ2	OFF	OFF	OFF	ON

IRQ3	OFF	OFF	ON	OFF

IRQ5	OFF	ON	OFF	OFF

IRQ7	ON	OFF	OFF	OFF

Base I/O Address

SW1

S1	S2

0A20h	ON	ON

1A20h	OFF	ON

2A20h	ON	OFF

3A20h	OFF	OFF

Base Memory Address

NOT USED

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector

Shielded Twisted Pair via DB-9 Connector


Madge Networks Smart 16/4 AT RingNode

This is the Madge Networks Smart 16/4 AT RingNode Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

SW1

S1	S2	S3	S4	S5	S6	S7	S8

IRQ2/9	OFF	OFF	OFF	OFF	OFF	OFF	OFF	ON

IRQ3	OFF	OFF	OFF	OFF	OFF	OFF	ON	OFF

IRQ5	OFF	OFF	OFF	OFF	OFF	ON	OFF	OFF

IRQ7	OFF	OFF	OFF	OFF	ON	OFF	OFF	OFF

IRQ10	OFF	OFF	OFF	ON	OFF	OFF	OFF	OFF

IRQ11	OFF	OFF	ON	OFF	OFF	OFF	OFF	OFF

IRQ12	OFF	ON	OFF	OFF	OFF	OFF	OFF	OFF

IRQ15	ON	OFF	OFF	OFF	OFF	OFF	OFF	OFF

Base I/O Address

SW2

S1	S2

0A20h	ON	ON

1A20h	OFF	ON

2A20h	ON	OFF

3A20h	OFF	OFF

Base Memory Address

NOT USED

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector

Shielded Twisted Pair via DB-9 Connector


Madge Networks Smart 16/4 EISA RingNode

This can be configured using the ECU (EISA Configuration Utility) that ships with most EISA systems. For question about use of the ECU, please consult the documentation that came with your system or contact the manufacturer of the system.

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector

Shielded Twisted Pair via DB-9 Connector


Madge Networks Smart 16/4 MC RingNode

This Network Adapter card is configured using the 'Reference Disk' provided with your Micro-Channel System.  For further information consult the documentation provided with the Network Adapter or contact your vendor.

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector

Shielded Twisted Pair via DB-9 Connector


NCR Cards
NCR

Windows 95 Adapter help currently includes the following NCR network cards:

NCR WaveLan AT Adapter

NCR WaveLan MC Adapter


NCR WaveLan AT Adapter Card
NCR WaveLan AT Adapter

This is the NCR WaveLan AT Adapter Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

NOT USED

Base I/O Address

SW1

S1	S2

300h	OFF	OFF

390h	OFF	ON

3C0h	ON	OFF

3E0h	ON	ON

Base Memory Address

NOT USED

Cabling for this Adapter

Thin Ethernet via BNC Connector


NCR WaveLan MC Adapter Card
NCR WaveLan MC Adapter

This Network Adapter card is configured using the 'Reference Disk' provided with your Micro-Channel System.  For further information consult the documentation provided with the Network Adapter or contact your vendor.

Cabling for this Adapter

Thin Ethernet via BNC Connector


Networth Cards
Networth

Windows 95 Adapter help currently includes the following Networth network cards:

Networth EtherneXt 16-bit UTP

Networth EtherneXt 16-bit UTP (MCA)


Networth EtherneXt 16-bit UTP Card
Networth EtherneXt 16-bit UTP

This is the Networth EtherneXt 16-bit UTP Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

W6

J2	J3	J4	J5	J10	J11	J12	J15

IRQ2	ON	OFF	OFF	OFF	OFF	OFF	OFF	OFF

IRQ3	OFF	ON	OFF	OFF	OFF	OFF	OFF	OFF

IRQ4	OFF	OFF	ON	OFF	OFF	OFF	OFF	OFF

IRQ5	OFF	OFF	OFF	ON	OFF	OFF	OFF	OFF

IRQ10	OFF	OFF	OFF	OFF	ON	OFF	OFF	OFF

IRQ11	OFF	OFF	OFF	OFF	OFF	ON	OFF	OFF

IRQ12	OFF	OFF	OFF	OFF	OFF	OFF	ON	OFF

IRQ15	OFF	OFF	OFF	OFF	OFF	OFF	OFF	ON

Base I/O Address

W5

BIOA	BIOB

300h	ON	ON

320h	OFF	ON

340h	ON	OFF

360h	OFF	OFF

Base Memory Address

NOT USED

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector

Thick Ethernet via AUI Connector


Networth EtherneXt 16-bit UTP (MCA) Card
Networth EtherneXt 16-bit UTP (MCA)

This Network Adapter card is configured using the 'Reference Disk' provided with your Micro-Channel System.  For further information consult the documentation provided with the Network Adapter or contact your vendor.

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector

Thick Ethernet via AUI Connector


Novell Cards
Novell

Windows 95 Adapter help currently includes the following Novell network cards:

Novell-Anthem NE1000 (Assy. 950-054401)

Novell-Anthem NE1000 (Assy. 810-160-001)

Novell-Anthem NE2000

Novell NE3200Novell-Anthem NE-2


Novell-Anthem NE1000 Card (Assy. 950-054401)
Novell-Anthem NE1000 (Assy. 950-054401)

This is the Novell-Anthem NE1000 Card (Assy. 950-054401) shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

J1	J2	J3	J4

IRQ2	ON	OFF	OFF	OFF

IRQ3	OFF	ON	OFF	OFF

IRQ4	OFF	OFF	ON	OFF

IRQ5	OFF	OFF	OFF	ON

Base I/O Address

J9	J10

300h	ON	ON

320h	OFF	ON

340h	ON	OFF

360h	OFF	OFF

Base Memory Address

NOT USED

Cabling for this Adapter

Thick Ethernet via AUI Connector

Thin Ethernet via BNC Connector


Novell-Anthem NE1000 Card (Assy. 810-160-001)
Novell-Anthem NE1000 (Assy. 810-160-001)

This is the Novell-Anthem NE1000 Card (Assy. 810-160-001) shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

W12	W13	W14	W15

IRQ2	ON	OFF	OFF	OFF

IRQ3	OFF	ON	OFF	OFF

IRQ4	OFF	OFF	ON	OFF

IRQ5	OFF	OFF	OFF	ON

Base I/O Address

W9	W10	W11

300h	ON	ON	OFF

320h	OFF	ON	OFF

340h	ON	OFF	OFF

360h	OFF	OFF	OFF

Base Memory Address

NOT USED

Cabling for this Adapter

Thick Ethernet via AUI Connector

Thin Ethernet via BNC Connector


Novell-Anthem NE2000 Card
Novell-Anthem NE2000

This is the Novell-Anthem NE2000 Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

W12	W13	W14	W15

IRQ2	ON	OFF	OFF	OFF

IRQ3	OFF	ON	OFF	OFF

IRQ4	OFF	OFF	ON	OFF

IRQ5	OFF	OFF	OFF	ON

Base I/O Address

W9	W10	W11

300h	ON	ON	OFF

320h	OFF	ON	OFF

340h	ON	OFF	OFF

360h	OFF	OFF	OFF

Base Memory Address

NOT USED

Cabling for this Adapter

Thick Ethernet via AUI Connector

Thin Ethernet via BNC Connector


Novell-Anthem NE-2 Card
Novell-Anthem NE-2

This Network Adapter card is configured using the 'Reference Disk' provided with your Micro-Channel System.  For further information consult the documentation provided with the Network Adapter or contact your vendor.

Interrupt Request Line (IRQ)

Default - IRQ3

Base I/O Address

Default - 1000h

Cabling for this Adapter

Thick Ethernet via AUI Connector

Thin Ethernet via BNC Connector


Novell NE3200 Card
Novell NE3200

This can be configured using the ECU (EISA Configuration Utility) that ships with most EISA systems. For question about use of the ECU, please consult the documentation that came with your system or contact the manufacturer of the system.

Cabling for this Adapter

Thick Ethernet via AUI Connector

Thin Ethernet via BNC Connector


Olicom Cards
Olicom

Windows 95 Adapter help currently includes the following Olicom network cards:

Olicom 16-4 Token Ring Adapter (ISA)

Olicom 16-4 Token Ring Adapter (MCA)

Olicom 16-4 Token Ring Adapter (EISA)


Olicom 16-4 Token Ring Adapter

This is the Olicom 16/4 Token Ring Adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

SW2

S7	S8

IRQ2/9	ON	ON

IRQ3	ON	OFF

IRQ10	OFF	ON

IRQ11	OFF	OFF

Base I/O Address

SW2

S9	S10

0A20h	OFF	OFF

0A24h	ON	OFF

0A50h	OFF	ON

0A54h	ON	ON

Base Memory Address

NOT USED

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector

Shielded Twisted Pair (IBM Type 1) via DB-9 Connector


Olicom 16-4 Token Ring Adapter (MCA)

This Network Adapter card is configured using the 'Reference Disk' provided with your Micro-Channel System.  For further information consult the documentation provided with the Network Adapter or contact your vendor.

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector

Shielded Twisted Pair via DB-9 Connector


Olicom 16-4 Token Ring Adapter (EISA)

This can be configured using the ECU (EISA Configuration Utility) that ships with most EISA systems. For question about use of the ECU, please consult the documentation that came with your system or contact the manufacturer of the system.

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector

Shielded Twisted Pair (IBM Type 1) via DB-9 Connector


Proteon Cards
Proteon

Windows 95 Adapter help currently includes the following Proteon network cards:

Proteon Token Ring (P1390)

Proteon Token Ring (P1392)

Proteon EISA Token Ring

Proteon ISA Token Ring (P1340)


Proteon EISA Token Ring Card
Proteon EISA Token Ring

This can be configured using the ECU (EISA Configuration Utility) that ships with most EISA systems. For question about use of the ECU, please consult the documentation that came with your system or contact the manufacturer of the system.

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector

Shielded Twisted Pair (IBM Type 1) via DB-9 Connector


Proteon  Token Ring (P1390) Card
Proteon Token Ring (P1390)

This is the Proteon Token Ring (P1390) Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

J3	J4	J5	J6	J7	J9	J10	J11	J12

IRQ3	ON	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF

IRQ4	OFF	ON	OFF	OFF	OFF	OFF	OFF	OFF	OFF

IRQ5	OFF	OFF	ON	OFF	OFF	OFF	OFF	OFF	OFF

IRQ6	OFF	OFF	OFF	ON	OFF	OFF	OFF	OFF	OFF

IRQ7	OFF	OFF	OFF	OFF	ON	OFF	OFF	OFF	OFF

IRQ9	OFF	OFF	OFF	OFF	OFF	ON	OFF	OFF	OFF

IRQ10	OFF	OFF	OFF	OFF	OFF	OFF	ON	OFF	OFF

IRQ11	OFF	OFF	OFF	OFF	OFF	OFF	OFF	ON	OFF

IRQ12	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF	ON

Base I/O Address

J8	J9	J10	J11	J12	J13	J14	J15

0A20h	ON	OFF	ON	OFF	ON	ON	ON	ON

1A20h	ON	OFF	ON	OFF	OFF	ON	ON	ON

2A20h	ON	OFF	ON	OFF	ON	OFF	ON	ON

3A20h	ON	OFF	ON	OFF	ON	ON	ON	ON

4A20h	ON	OFF	ON	OFF	ON	ON	ON	ON

5A20h	ON	OFF	ON	OFF	ON	ON	ON	ON

Base Memory Address

NOT USED

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector

Shielded Twisted Pair (IBM Type 1) via DB-9 Connector


Proteon Token Ring (P1392) Card
Proteon Token Ring (P1392)

This is the Proteon Token Ring (P1392) Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

NOT USED

Base I/O Address

J2	J3	J4	J5	J6

0A20h	ON	ON	ON	ON	ON

0E20h	OFF	ON	ON	ON	ON

1A20h	ON	OFF	ON	ON	ON

1E20h	OFF	OFF	ON	ON	ON

2A20h	ON	ON	OFF	ON	ON

2E20h	OFF	ON	OFF	ON	ON

3A20h	ON	OFF	OFF	ON	ON

3E20h	OFF	OFF	OFF	ON	ON

4A20h	ON	ON	ON	OFF	ON

4E20h	OFF	ON	ON	OFF	ON

5A20h	ON	OFF	ON	OFF	ON

5E20h	OFF	OFF	ON	OFF	ON

6A20h	ON	ON	OFF	OFF	ON

6E20h	OFF	ON	OFF	OFF	ON

7A20h	ON	OFF	OFF	OFF	ON

7E20h	OFF	OFF	OFF	OFF	ON

8A20h	ON	ON	ON	ON	OFF

8E20h	OFF	ON	ON	ON	OFF

9A20h	ON	OFF	ON	ON	OFF

9E20h	OFF	OFF	ON	ON	OFF

AA20h	ON	ON	OFF	ON	OFF

AE20h	OFF	ON	OFF	ON	OFF

BA20h	ON	OFF	OFF	ON	OFF

BE20h	OFF	OFF	OFF	ON	OFF

CA20h	ON	ON	ON	OFF	OFF

CE20h	OFF	ON	ON	OFF	OFF

DA20h	ON	OFF	ON	OFF	OFF

DE20h	OFF	OFF	ON	OFF	OFF

EA20h	ON	ON	OFF	OFF	OFF

EE20h	OFF	ON	OFF	OFF	OFF

FA20h	ON	OFF	OFF	OFF	OFF

FE20h	OFF	OFF	OFF	OFF	OFF

Base Memory Address

NOT USED

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector

Shielded Twisted Pair (IBM Type 1) via DB-9 Connector


Proteon ISA Token Ring (P1340) Card
Proteon ISA Token Ring (P1340)

This is the Proteon ISA Token Ring (P1340) Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

JP3

J1	J2	J3	J4	J5	J6

IRQ2	ON	OFF	OFF	OFF	OFF	OFF

IRQ3	OFF	ON	OFF	OFF	OFF	OFF

IRQ4	OFF	OFF	ON	OFF	OFF	OFF

IRQ5	OFF	OFF	OFF	ON	OFF	OFF

IRQ6	OFF	OFF	OFF	OFF	ON	OFF

IRQ7	OFF	OFF	OFF	OFF	OFF	ON

Base I/O Address

JP1

J1	J2	J3	J4	J5	J6	J7	J8	J9	J10	J11	J12

0200h	ON	ON	ON	ON	ON	OFF	ON	ON	ON	ON	ON	ON

0210h	OFF	ON	ON	ON	ON	OFF	ON	ON	ON	ON	ON	ON

0220h	ON	OFF	ON	ON	ON	OFF	ON	ON	ON	ON	ON	ON

0230h	OFF	OFF	ON	ON	ON	OFF	ON	ON	ON	ON	ON	ON

0240h	ON	ON	OFF	ON	ON	OFF	ON	ON	ON	ON	ON	ON

0250h	OFF	ON	OFF	ON	ON	OFF	ON	ON	ON	ON	ON	ON

0260h	ON	OFF	OFF	ON	ON	OFF	ON	ON	ON	ON	ON	ON

0270h	OFF	OFF	OFF	ON	ON	OFF	ON	ON	ON	ON	ON	ON

0280h	ON	ON	ON	OFF	ON	OFF	ON	ON	ON	ON	ON	ON

0290h	OFF	ON	ON	OFF	ON	OFF	ON	ON	ON	ON	ON	ON

02A0h	ON	OFF	ON	OFF	ON	OFF	ON	ON	ON	ON	ON	ON

02B0h	OFF	OFF	ON	OFF	ON	OFF	ON	ON	ON	ON	ON	ON

02C0h	ON	ON	OFF	OFF	ON	OFF	ON	ON	ON	ON	ON	ON

02D0h	OFF	ON	OFF	OFF	ON	OFF	ON	ON	ON	ON	ON	ON

02E0h	ON	OFF	OFF	OFF	ON	OFF	ON	ON	ON	ON	ON	ON

02F0h	OFF	OFF	OFF	OFF	ON	OFF	ON	ON	ON	ON	ON	ON

0300h	ON	ON	ON	ON	OFF	OFF	ON	ON	ON	ON	ON	ON

0310h	OFF	ON	ON	ON	OFF	OFF	ON	ON	ON	ON	ON	ON

0320h	ON	OFF	ON	ON	OFF	OFF	ON	ON	ON	ON	ON	ON

0330h	OFF	OFF	ON	ON	OFF	OFF	ON	ON	ON	ON	ON	ON

0340h	ON	ON	OFF	ON	OFF	OFF	ON	ON	ON	ON	ON	ON

0350h	OFF	ON	OFF	ON	OFF	OFF	ON	ON	ON	ON	ON	ON

0360h	ON	OFF	OFF	ON	OFF	OFF	ON	ON	ON	ON	ON	ON

0370h	OFF	OFF	OFF	ON	OFF	OFF	ON	ON	ON	ON	ON	ON

0380h	ON	ON	ON	OFF	OFF	OFF	ON	ON	ON	ON	ON	ON

0390h	OFF	ON	ON	OFF	OFF	OFF	ON	ON	ON	ON	ON	ON

03A0h	ON	OFF	ON	OFF	OFF	OFF	ON	ON	ON	ON	ON	ON

03B0h	OFF	OFF	ON	OFF	OFF	OFF	ON	ON	ON	ON	ON	ON

03C0h	ON	ON	OFF	OFF	OFF	OFF	ON	ON	ON	ON	ON	ON

03D0h	OFF	ON	OFF	OFF	OFF	OFF	ON	ON	ON	ON	ON	ON

03E0h	ON	OFF	OFF	OFF	OFF	OFF	ON	ON	ON	ON	ON	ON

03F0h	OFF	OFF	OFF	OFF	OFF	OFF	ON	ON	ON	ON	ON	ON

0A00h	ON	ON	ON	ON	ON	OFF	ON	OFF	ON	ON	ON	ON

0A10h	OFF	ON	ON	ON	ON	OFF	ON	OFF	ON	ON	ON	ON

0A20h	ON	OFF	ON	ON	ON	OFF	ON	OFF	ON	ON	ON	ON

0A30h	OFF	OFF	ON	ON	ON	OFF	ON	OFF	ON	ON	ON	ON

0A40h	ON	ON	OFF	ON	ON	OFF	ON	OFF	ON	ON	ON	ON

0A50h	OFF	ON	OFF	ON	ON	OFF	ON	OFF	ON	ON	ON	ON

0A60h	ON	OFF	OFF	ON	ON	OFF	ON	OFF	ON	ON	ON	ON

0A70h	OFF	OFF	OFF	ON	ON	OFF	ON	OFF	ON	ON	ON	ON

0A80h	ON	ON	ON	OFF	ON	OFF	ON	OFF	ON	ON	ON	ON

0A90h	OFF	ON	ON	OFF	ON	OFF	ON	OFF	ON	ON	ON	ON

0AA0h	ON	OFF	ON	OFF	ON	OFF	ON	OFF	ON	ON	ON	ON

0AB0h	OFF	OFF	ON	OFF	ON	OFF	ON	OFF	ON	ON	ON	ON

0AC0h	ON	ON	OFF	OFF	ON	OFF	ON	OFF	ON	ON	ON	ON

0AD0h	OFF	ON	OFF	OFF	ON	OFF	ON	OFF	ON	ON	ON	ON

0AE0h	ON	OFF	OFF	OFF	ON	OFF	ON	OFF	ON	ON	ON	ON

0AF0h	OFF	OFF	OFF	OFF	ON	OFF	ON	OFF	ON	ON	ON	ON

Base Memory Address

JP2

J1	J2	J3	J4	J5	J6	J7

0000h	ON	ON	ON	ON	ON	ON	ON

0200h	OFF	ON	ON	ON	ON	ON	ON

0400h	ON	OFF	ON	ON	ON	ON	ON

0600h	OFF	OFF	ON	ON	ON	ON	ON

0800h	ON	ON	OFF	ON	ON	ON	ON

0A00h	OFF	ON	OFF	ON	ON	ON	ON

0C00h	ON	OFF	OFF	ON	ON	ON	ON

0E00h	OFF	OFF	OFF	ON	ON	ON	ON

1000h	ON	ON	ON	OFF	ON	ON	ON

1200h	OFF	ON	ON	OFF	ON	ON	ON

1400h	ON	OFF	ON	OFF	ON	ON	ON

1600h	OFF	OFF	ON	OFF	ON	ON	ON

1800h	ON	ON	OFF	OFF	ON	ON	ON

1A00h	OFF	ON	OFF	OFF	ON	ON	ON

1C00h	ON	OFF	OFF	OFF	ON	ON	ON

1E00h	OFF	OFF	OFF	OFF	ON	ON	ON

2000h	ON	ON	ON	ON	OFF	ON	ON

2200h	OFF	ON	ON	ON	OFF	ON	ON

2400h	ON	OFF	ON	ON	OFF	ON	ON

2600h	OFF	OFF	ON	ON	OFF	ON	ON

2800h	ON	ON	OFF	ON	OFF	ON	ON

2A00h	OFF	ON	OFF	ON	OFF	ON	ON

2C00h	ON	OFF	OFF	ON	OFF	ON	ON

2E00h	OFF	OFF	OFF	ON	OFF	ON	ON

3000h	ON	ON	ON	OFF	OFF	ON	ON

3200h	OFF	ON	ON	OFF	OFF	ON	ON

3400h	ON	OFF	ON	OFF	OFF	ON	ON

3600h	OFF	OFF	ON	OFF	OFF	ON	ON

3800h	ON	ON	OFF	OFF	OFF	ON	ON

3A00h	OFF	ON	OFF	OFF	OFF	ON	ON

3C00h	ON	OFF	OFF	OFF	OFF	ON	ON

3E00h	OFF	OFF	OFF	OFF	OFF	ON	ON

4000h	ON	ON	ON	ON	ON	OFF	ON

4200h	OFF	ON	ON	ON	ON	OFF	ON

4400h	ON	OFF	ON	ON	ON	OFF	ON

4600h	OFF	OFF	ON	ON	ON	OFF	ON

4800h	ON	ON	OFF	ON	ON	OFF	ON

4A00h	OFF	ON	OFF	ON	ON	OFF	ON

4C00h	ON	OFF	OFF	ON	ON	OFF	ON

4E00h	OFF	OFF	OFF	ON	ON	OFF	ON

5000h	ON	ON	ON	OFF	ON	OFF	ON

5200h	OFF	ON	ON	OFF	ON	OFF	ON

5400h	ON	OFF	ON	OFF	ON	OFF	ON

5600h	OFF	OFF	ON	OFF	ON	OFF	ON

5800h	ON	ON	OFF	OFF	ON	OFF	ON

5A00h	OFF	ON	OFF	OFF	ON	OFF	ON

5C00h	ON	OFF	OFF	OFF	ON	OFF	ON

5E00h	OFF	OFF	OFF	OFF	ON	OFF	ON

6000h	ON	ON	ON	ON	OFF	OFF	ON

6200h	OFF	ON	ON	ON	OFF	OFF	ON

6400h	ON	OFF	ON	ON	OFF	OFF	ON

6600h	OFF	OFF	ON	ON	OFF	OFF	ON

6800h	ON	ON	OFF	ON	OFF	OFF	ON

6A00h	OFF	ON	OFF	ON	OFF	OFF	ON

6C00h	ON	OFF	OFF	ON	OFF	OFF	ON

6E00h	OFF	OFF	OFF	ON	OFF	OFF	ON

7000h	ON	ON	ON	OFF	OFF	OFF	ON

7200h	OFF	ON	ON	OFF	OFF	OFF	ON

7400h	ON	OFF	ON	OFF	OFF	OFF	ON

7600h	OFF	OFF	ON	OFF	OFF	OFF	ON

7800h	ON	ON	OFF	OFF	OFF	OFF	ON

7A00h	OFF	ON	OFF	OFF	OFF	OFF	ON

7C00h	ON	OFF	OFF	OFF	OFF	OFF	ON

7E00h	OFF	OFF	OFF	OFF	OFF	OFF	ON

8000h	ON	ON	ON	ON	ON	ON	OFF

8200h	OFF	ON	ON	ON	ON	ON	OFF

8400h	ON	OFF	ON	ON	ON	ON	OFF

8600h	OFF	OFF	ON	ON	ON	ON	OFF

8800h	ON	ON	OFF	ON	ON	ON	OFF

8A00h	OFF	ON	OFF	ON	ON	ON	OFF

8C00h	ON	OFF	OFF	ON	ON	ON	OFF

8E00h	OFF	OFF	OFF	ON	ON	ON	OFF

9000h	ON	ON	ON	OFF	ON	ON	OFF

9200h	OFF	ON	ON	OFF	ON	ON	OFF

9400h	ON	OFF	ON	OFF	ON	ON	OFF

9600h	OFF	OFF	ON	OFF	ON	ON	OFF

9800h	ON	ON	OFF	OFF	ON	ON	OFF

9A00h	OFF	ON	OFF	OFF	ON	ON	OFF

9C00h	ON	OFF	OFF	OFF	ON	ON	OFF

9E00h	OFF	OFF	OFF	OFF	ON	ON	OFF

A000h	ON	ON	ON	ON	OFF	ON	OFF

A200h	OFF	ON	ON	ON	OFF	ON	OFF

A400h	ON	OFF	ON	ON	OFF	ON	OFF

A600h	OFF	OFF	ON	ON	OFF	ON	OFF

A800h	ON	ON	OFF	ON	OFF	ON	OFF

AA00h	OFF	ON	OFF	ON	OFF	ON	OFF

AC00h	ON	OFF	OFF	ON	OFF	ON	OFF

AE00h	OFF	OFF	OFF	ON	OFF	ON	OFF

B000h	ON	ON	ON	OFF	OFF	ON	OFF

B200h	OFF	ON	ON	OFF	OFF	ON	OFF

B400h	ON	OFF	ON	OFF	OFF	ON	OFF

B600h	OFF	OFF	ON	OFF	OFF	ON	OFF

B800h	ON	ON	OFF	OFF	OFF	ON	OFF

BA00h	OFF	ON	OFF	OFF	OFF	ON	OFF

BC00h	ON	OFF	OFF	OFF	OFF	ON	OFF

BE00h	OFF	OFF	OFF	OFF	OFF	ON	OFF

C000h	ON	ON	ON	ON	ON	OFF	OFF

C200h	OFF	ON	ON	ON	ON	OFF	OFF

C400h	ON	OFF	ON	ON	ON	OFF	OFF

C600h	OFF	OFF	ON	ON	ON	OFF	OFF

C800h	ON	ON	OFF	ON	ON	OFF	OFF

CA00h	OFF	ON	OFF	ON	ON	OFF	OFF

CC00h	ON	OFF	OFF	ON	ON	OFF	OFF

CE00h	OFF	OFF	OFF	ON	ON	OFF	OFF

D000h	ON	ON	ON	OFF	ON	OFF	OFF

D200h	OFF	ON	ON	OFF	ON	OFF	OFF

D400h	ON	OFF	ON	OFF	ON	OFF	OFF

D600h	OFF	OFF	ON	OFF	ON	OFF	OFF

D800h	ON	ON	OFF	OFF	ON	OFF	OFF

DA00h	OFF	ON	OFF	OFF	ON	OFF	OFF

DC00h	ON	OFF	OFF	OFF	ON	OFF	OFF

DE00h	OFF	OFF	OFF	OFF	ON	OFF	OFF

E000h	ON	ON	ON	ON	OFF	OFF	OFF

E200h	OFF	ON	ON	ON	OFF	OFF	OFF

E400h	ON	OFF	ON	ON	OFF	OFF	OFF

E600h	OFF	OFF	ON	ON	OFF	OFF	OFF

E800h	ON	ON	OFF	ON	OFF	OFF	OFF

EA00h	OFF	ON	OFF	ON	OFF	OFF	OFF

EC00h	ON	OFF	OFF	ON	OFF	OFF	OFF

EE00h	OFF	OFF	OFF	ON	OFF	OFF	OFF

F000h	ON	ON	ON	OFF	OFF	OFF	OFF

F200h	OFF	ON	ON	OFF	OFF	OFF	OFF

F400h	ON	OFF	ON	OFF	OFF	OFF	OFF

F600h	OFF	OFF	ON	OFF	OFF	OFF	OFF

F800h	ON	ON	OFF	OFF	OFF	OFF	OFF

FA00h	OFF	ON	OFF	OFF	OFF	OFF	OFF

FC00h	ON	OFF	OFF	OFF	OFF	OFF	OFF

FE00h	OFF	OFF	OFF	OFF	OFF	OFF	OFF

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector

Shielded Twisted Pair (IBM Type 1) via DB-9 Connector


Pure Data Cards
Pure Data

Windows 95 Adapter help currently includes the following Pure Data network cards:

Pure Data PDI9025-16 (Token Ring)

Pure Data PDE9025-32 (Token Ring)

Pure Data PDuC9025 (Token Ring)

Pure Data PDI508+ (ArcNet)

Pure Data PDI516+ (ArcNet)


Pure Data PDI9025-16 (Token Ring) Card
Pure Data PDI9025-16 (Token Ring)

This is the Pure Data PDI9025-16 (Token Ring) Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

SW2

S7	S8

IRQ2/9	ON	ON

IRQ3	ON	OFF

IRQ10	OFF	ON

IRQ11	OFF	OFF

Base I/O Address

SW2

S9	S10

A20h	OFF	OFF

A24h	ON	OFF

A50h	OFF	ON

A54h	ON	ON

Base Memory Address

NOT USED

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector

Shielded Twisted Pair via DB-9 Connector


Pure Data PDI9025-32 (Token Ring) Card
Pure Data PDE9025-32 (Token Ring)

This can be configured using the ECU (EISA Configuration Utility) that ships with most EISA systems. For question about use of the ECU, please consult the documentation that came with your system or contact the manufacturer of the system.

Interrupt Request Line (IRQ)

Default - IRQ2

Base I/O Address

Default - A20h

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector

Shielded Twisted Pair via DB-9 Connector


Pure Data PDuC9025 (Token Ring) Card
Pure Data PDuC9025 (Token Ring)

This Network Adapter card is configured using the 'Reference Disk' provided with your Micro-Channel System.  For further information consult the documentation provided with the Network Adapter or contact your vendor.

Interrupt Request Line (IRQ)

Default - IRQ2

Base I/O Address

Default - A20h

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector

Shielded Twisted Pair via DB-9 Connector


Pure Data PDI508+ (ArcNet) Card
Pure Data PDI508+(ArcNet)

This is the Pure Data PDI508+ (ArcNet) Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

JP2

J1	J2	J3

IRQ2	SOFTWARE

IRQ3	SOFTWARE

IRQ4	SOFTWARE

IRQ5	ON	OFF	OFF

IRQ6	OFF	ON	OFF

IRQ7	OFF	OFF	ON

Base I/O Address

SOFTWARE CONFIGURABLE

Default - 2E0h

Base Memory Address

SOFTWARE CONFIGURABLE

Default - D000h

Cabling for this Adapter

Thin Ethernet via BNC Connector


Pure Data PD516+ (ArcNet) Card
Pure Data PDI516+(ArcNet)

This Network Adapter card can be configured using the software supplied by the manufacturer. Please consult the documentation that came with your Network Adapter or contact the manufacturer of the Network Adapter for further information.

Interrupt Request Line (IRQ)

Default - IRQ2

Base I/O Address

Default - 2E0h

Base Memory Address

Default - D000h

Cabling for this Adapter

Thin Ethernet via BNC Connector


Racal Cards
Racal

Windows 95 Adapter help currently includes the following Racal network cards:

Racal NI5210-8

Racal NI5210-16


Racal NI5210-8 Card
Racal NI5210-8

This is the Racal NI5210-8 Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

J2	J3	J4	J5	J6	J7

IRQ2	ON	OFF	OFF	OFF	OFF	OFF

IRQ3	OFF	ON	OFF	OFF	OFF	OFF

IRQ4	OFF	OFF	ON	OFF	OFF	OFF

IRQ5	OFF	OFF	OFF	ON	OFF	OFF

IRQ6	OFF	OFF	OFF	OFF	ON	OFF

IRQ7	OFF	OFF	OFF	OFF	OFF	ON

Base I/O Address

J3	J4	J5	J6	J7	J8

200h	1-2	1-2	1-2	1-2	1-2	1-2

208h	1-2	1-2	1-2	1-2	1-2	2-3

210h	1-2	1-2	1-2	1-2	2-3	1-2

218h	1-2	1-2	1-2	1-2	2-3	2-3

220h	1-2	1-2	1-2	2-3	1-2	1-2

228h	1-2	1-2	1-2	2-3	1-2	2-3

230h	1-2	1-2	1-2	2-3	2-3	1-2

238h	1-2	1-2	1-2	2-3	2-3	2-3

240h	1-2	1-2	2-3	1-2	1-2	1-2

248h	1-2	1-2	2-3	1-2	1-2	2-3

250h	1-2	1-2	2-3	1-2	2-3	1-2

258h	1-2	1-2	2-3	1-2	2-3	2-3

260h	1-2	1-2	2-3	2-3	1-2	1-2

268h	1-2	1-2	2-3	2-3	1-2	2-3

270h	1-2	1-2	2-3	2-3	2-3	1-2

278h	1-2	1-2	2-3	2-3	2-3	2-3

280h	1-2	2-3	1-2	1-2	1-2	1-2

288h	1-2	2-3	1-2	1-2	1-2	2-3

290h	1-2	2-3	1-2	1-2	2-3	1-2

298h	1-2	2-3	1-2	1-2	2-3	2-3

2A0h	1-2	2-3	1-2	2-3	1-2	1-2

2A8h	1-2	2-3	1-2	2-3	1-2	2-3

2B0h	1-2	2-3	1-2	2-3	2-3	1-2

2B8h	1-2	2-3	1-2	2-3	2-3	2-3

2C0h	1-2	2-3	2-3	1-2	1-2	1-2

2C8h	1-2	2-3	2-3	1-2	1-2	2-3

2D0h	1-2	2-3	2-3	1-2	2-3	1-2

2D8h	1-2	2-3	2-3	1-2	2-3	2-3

2E0h	1-2	2-3	2-3	2-3	1-2	1-2

2E8h	1-2	2-3	2-3	2-3	1-2	2-3

2F0h	1-2	2-3	2-3	2-3	2-3	1-2

2F8h	1-2	2-3	2-3	2-3	2-3	2-3

300h	2-3	1-2	1-2	1-2	1-2	1-2

308h	2-3	1-2	1-2	1-2	1-2	2-3

310h	2-3	1-2	1-2	1-2	2-3	1-2

318h	2-3	1-2	1-2	1-2	2-3	2-3

320h	2-3	1-2	1-2	2-3	1-2	1-2

328h	2-3	1-2	1-2	2-3	1-2	2-3

330h	2-3	1-2	1-2	2-3	2-3	1-2

338h	2-3	1-2	1-2	2-3	2-3	2-3

340h	2-3	1-2	2-3	1-2	1-2	1-2

348h	2-3	1-2	2-3	1-2	1-2	2-3

350h	2-3	1-2	2-3	1-2	2-3	1-2

358h	2-3	1-2	2-3	1-2	2-3	2-3

360h	2-3	1-2	2-3	2-3	1-2	1-2

368h	2-3	1-2	2-3	2-3	1-2	2-3

370h	2-3	1-2	2-3	2-3	2-3	1-2

378h	2-3	1-2	2-3	2-3	2-3	2-3

380h	2-3	2-3	1-2	1-2	1-2	1-2

388h	2-3	2-3	1-2	1-2	1-2	2-3

390h	2-3	2-3	1-2	1-2	2-3	1-2

398h	2-3	2-3	1-2	1-2	2-3	2-3

3A0h	2-3	2-3	1-2	2-3	1-2	1-2

3A8h	2-3	2-3	1-2	2-3	1-2	2-3

3B0h	2-3	2-3	1-2	2-3	2-3	1-2

3B8h	2-3	2-3	1-2	2-3	2-3	2-3

3C0h	2-3	2-3	2-3	1-2	1-2	1-2

3C8h	2-3	2-3	2-3	1-2	1-2	2-3

3D0h	2-3	2-3	2-3	1-2	2-3	1-2

3D8h	2-3	2-3	2-3	1-2	2-3	2-3

3E0h	2-3	2-3	2-3	2-3	1-2	1-2

3E8h	2-3	2-3	2-3	2-3	1-2	2-3

3F0h	2-3	2-3	2-3	2-3	2-3	1-2

3F8h	2-3	2-3	2-3	2-3	2-3	2-3

Base Memory Address

J14	J15	J16	J17

C000h	1-2	1-2	1-2	1-2

C400h	1-2	1-2	1-2	2-3

C800h	1-2	1-2	2-3	1-2

CC00h	1-2	1-2	2-3	2-3

D000h	1-2	2-3	1-2	1-2

D400h	1-2	2-3	1-2	2-3

D800h	1-2	2-3	2-3	1-2

DC00h	1-2	2-3	2-3	2-3

E000h	2-3	1-2	1-2	1-2

E400h	2-3	1-2	1-2	2-3

E800h	2-3	1-2	2-3	1-2

EC00h	2-3	1-2	2-3	2-3

Cabling for this Adapter

Thick Ethernet via AUI Connector

Thin Ethernet via BNC Connector


Racal NI5210-16 Card
Racal NI5210-16

This is the Racal NI5210-16 Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

J2	J3	J4	J5	J6	J7

IRQ2	ON	OFF	OFF	OFF	OFF	OFF

IRQ3	OFF	ON	OFF	OFF	OFF	OFF

IRQ4	OFF	OFF	ON	OFF	OFF	OFF

IRQ5	OFF	OFF	OFF	ON	OFF	OFF

IRQ6	OFF	OFF	OFF	OFF	ON	OFF

IRQ7	OFF	OFF	OFF	OFF	OFF	ON

Base I/O Address

J3	J4	J5	J6	J7	J8

200h	1-2	1-2	1-2	1-2	1-2	1-2

208h	1-2	1-2	1-2	1-2	1-2	2-3

210h	1-2	1-2	1-2	1-2	2-3	1-2

218h	1-2	1-2	1-2	1-2	2-3	2-3

220h	1-2	1-2	1-2	2-3	1-2	1-2

228h	1-2	1-2	1-2	2-3	1-2	2-3

230h	1-2	1-2	1-2	2-3	2-3	1-2

238h	1-2	1-2	1-2	2-3	2-3	2-3

240h	1-2	1-2	2-3	1-2	1-2	1-2

248h	1-2	1-2	2-3	1-2	1-2	2-3

250h	1-2	1-2	2-3	1-2	2-3	1-2

258h	1-2	1-2	2-3	1-2	2-3	2-3

260h	1-2	1-2	2-3	2-3	1-2	1-2

268h	1-2	1-2	2-3	2-3	1-2	2-3

270h	1-2	1-2	2-3	2-3	2-3	1-2

278h	1-2	1-2	2-3	2-3	2-3	2-3

280h	1-2	2-3	1-2	1-2	1-2	1-2

288h	1-2	2-3	1-2	1-2	1-2	2-3

290h	1-2	2-3	1-2	1-2	2-3	1-2

298h	1-2	2-3	1-2	1-2	2-3	2-3

2A0h	1-2	2-3	1-2	2-3	1-2	1-2

2A8h	1-2	2-3	1-2	2-3	1-2	2-3

2B0h	1-2	2-3	1-2	2-3	2-3	1-2

2B8h	1-2	2-3	1-2	2-3	2-3	2-3

2C0h	1-2	2-3	2-3	1-2	1-2	1-2

2C8h	1-2	2-3	2-3	1-2	1-2	2-3

2D0h	1-2	2-3	2-3	1-2	2-3	1-2

2D8h	1-2	2-3	2-3	1-2	2-3	2-3

2E0h	1-2	2-3	2-3	2-3	1-2	1-2

2E8h	1-2	2-3	2-3	2-3	1-2	2-3

2F0h	1-2	2-3	2-3	2-3	2-3	1-2

2F8h	1-2	2-3	2-3	2-3	2-3	2-3

300h	2-3	1-2	1-2	1-2	1-2	1-2

308h	2-3	1-2	1-2	1-2	1-2	2-3

310h	2-3	1-2	1-2	1-2	2-3	1-2

318h	2-3	1-2	1-2	1-2	2-3	2-3

320h	2-3	1-2	1-2	2-3	1-2	1-2

328h	2-3	1-2	1-2	2-3	1-2	2-3

330h	2-3	1-2	1-2	2-3	2-3	1-2

338h	2-3	1-2	1-2	2-3	2-3	2-3

340h	2-3	1-2	2-3	1-2	1-2	1-2

348h	2-3	1-2	2-3	1-2	1-2	2-3

350h	2-3	1-2	2-3	1-2	2-3	1-2

358h	2-3	1-2	2-3	1-2	2-3	2-3

360h	2-3	1-2	2-3	2-3	1-2	1-2

368h	2-3	1-2	2-3	2-3	1-2	2-3

370h	2-3	1-2	2-3	2-3	2-3	1-2

378h	2-3	1-2	2-3	2-3	2-3	2-3

380h	2-3	2-3	1-2	1-2	1-2	1-2

388h	2-3	2-3	1-2	1-2	1-2	2-3

390h	2-3	2-3	1-2	1-2	2-3	1-2

398h	2-3	2-3	1-2	1-2	2-3	2-3

3A0h	2-3	2-3	1-2	2-3	1-2	1-2

3A8h	2-3	2-3	1-2	2-3	1-2	2-3

3B0h	2-3	2-3	1-2	2-3	2-3	1-2

3B8h	2-3	2-3	1-2	2-3	2-3	2-3

3C0h	2-3	2-3	2-3	1-2	1-2	1-2

3C8h	2-3	2-3	2-3	1-2	1-2	2-3

3D0h	2-3	2-3	2-3	1-2	2-3	1-2

3D8h	2-3	2-3	2-3	1-2	2-3	2-3

3E0h	2-3	2-3	2-3	2-3	1-2	1-2

3E8h	2-3	2-3	2-3	2-3	1-2	2-3

3F0h	2-3	2-3	2-3	2-3	2-3	1-2

3F8h	2-3	2-3	2-3	2-3	2-3	2-3

Base Memory Address

J14	J15	J16	J17

C000h	1-2	1-2	1-2	1-2

C400h	1-2	1-2	1-2	2-3

C800h	1-2	1-2	2-3	1-2

CC00h	1-2	1-2	2-3	2-3

D000h	1-2	2-3	1-2	1-2

D400h	1-2	2-3	1-2	2-3

D800h	1-2	2-3	2-3	1-2

DC00h	1-2	2-3	2-3	2-3

E000h	2-3	1-2	1-2	1-2

E400h	2-3	1-2	1-2	2-3

E800h	2-3	1-2	2-3	1-2

EC00h	2-3	1-2	2-3	2-3

Cabling for this Adapter

Thick Ethernet via AUI Connector

Thin Ethernet via BNC Connector


Racore Computer Cards
Racore Computer

Windows 95 Adapter help currently includes the following Racore Computer  network cards:

Racore Computer M8113 16-4 Token Ring

Racore Computer M8114 16-4 Token Ring

Racore Computer M8115 16-4 Token Ring


Racore Computer M8113 16-4 Token Ring Card
Racore Computer M8113 16-4 Token Ring

This is the Racore Computer M8113 16-4 Token Ring Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

SW1

S3	S4

IRQ3	ON	ON

IRQ9	OFF	ON

IRQ10	ON	OFF

IRQ11	OFF	OFF

Base I/O Address

SW1

S1	S2

0A00h	ON	ON

0A20h	OFF	ON

0A40h	ON	OFF

0A60h	OFF	OFF

Base Memory Address

J5	J6

CC00h	ON	ON

D000h	OFF	ON

D800h	ON	OFF

DC00h	OFF	OFF

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector

Shielded Twisted Pair via DB-9 Connector


Racore Computer M8114 16-4 Token Ring Card
Racore Computer M8114 16-4 Token Ring

This Network Adapter card is configured using the 'Reference Disk' provided with your Micro-Channel System.  For further information consult the documentation provided with the Network Adapter or contact your vendor.

Interrupt Request Line (IRQ)

Default - IRQ2

Base I/O Address

Default - A20h

Base Memory Address

Default - CC00h

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector

Shielded Twisted Pair via DB-9 Connector


Racore Computer M8115 16-4 Token Ring Card
Racore Computer M8115 16-4 Token Ring

This is the Racore Computer M8115 16-4 Token Ring Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

SW1

S2

IRQ2	OFF

IRQ3	ON

Base I/O Address

SW1

S1

0A20h	ON

0A60h	OFF

Base Memory Address

SW1

S3

CC00h	ON

DC00h	OFF

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector

Shielded Twisted Pair via DB-9 Connector


SMC ARCNET Cards
SMC ARCNET

Windows 95 Adapter help currently includes the following SMC ARCNET network cards:

SMC ARCNETPC

SMC ARCNET PC100

SMC ARCNET PC110

SMC ARCNET PC130-E

SMC ARCNET PC220-120

SMC ARCNET PC270-E

SMC ARCNET PC500

SMC ARCNET PC550

SMC ARCNET PC600


SMC ARCNETPC Card
SMC ARCNETPC

This is the SMC ARCNETPC Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

JP1	JP2	JP3	JP4	JP5

IRQ2	OFF	OFF	OFF	OFF	ON

IRQ3	OFF	OFF	OFF	ON	OFF

IRQ4	OFF	OFF	ON	OFF	OFF

IRQ5	OFF	ON	OFF	OFF	OFF

IRQ7	ON	OFF	OFF	OFF	OFF

Base I/O Address

SW2

S1	S2	S3	S4	S5	S6

2E0h	OFF	ON	OFF	OFF	OFF	ON

2F0h	OFF	ON	OFF	OFF	OFF	OFF

300h	OFF	OFF	ON	ON	ON	ON

Base Memory Address

SW2

S7	S8	S9	S10

C000h	OFF	OFF	ON	ON

D000h	OFF	OFF	ON	OFF

Cabling for this Adapter

Thin Ethernet via BNC Connector


SMC ARCNET PC100 Card
SMC ARCNET PC100

This is the SMC ARCNET PC100 Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

JP1	JP2	JP3	JP4	JP5

IRQ2	OFF	OFF	OFF	OFF	ON

IRQ3	OFF	OFF	OFF	ON	OFF

IRQ4	OFF	OFF	ON	OFF	OFF

IRQ5	OFF	ON	OFF	OFF	OFF

IRQ7	ON	OFF	OFF	OFF	OFF

Base I/O Address

SW2

S1	S2	S3	S4	S5	S6

2E0h	OFF	ON	OFF	OFF	OFF	ON

2F0h	OFF	ON	OFF	OFF	OFF	OFF

300h	OFF	OFF	ON	ON	ON	ON

Base Memory Address

SW2

S7	S8	S9	S10

C000h	OFF	OFF	ON	ON

D000h	OFF	OFF	ON	OFF

Cabling for this Adapter

Thin Ethernet via BNC Connector


SMC ARCNET PC110 Card
SMC ARCNET PC110

This is the SMC ARCNET PC 110 Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

J3	J4	J5	J6	J7

IRQ2	ON	OFF	OFF	OFF	OFF

IRQ3	OFF	ON	OFF	OFF	OFF

IRQ4	OFF	OFF	ON	OFF	OFF

IRQ5	OFF	OFF	OFF	ON	OFF

IRQ7	OFF	OFF	OFF	OFF	ON

Base I/O Address

SW2

S1	S2	S3	S4	S5	S6

2E0h	OFF	ON	OFF	OFF	OFF	ON

2F0h	OFF	ON	OFF	OFF	OFF	OFF

300h	OFF	OFF	ON	ON	ON	ON

310h	OFF	OFF	ON	ON	ON	OFF

320h	OFF	OFF	ON	ON	OFF	ON

330h	OFF	OFF	ON	ON	OFF	OFF

340h	OFF	OFF	ON	OFF	ON	ON

350h	OFF	OFF	ON	OFF	ON	OFF

360h	OFF	OFF	ON	OFF	OFF	ON

370h	OFF	OFF	ON	OFF	OFF	OFF

380h	OFF	OFF	OFF	ON	ON	ON

Base Memory Address

SW2

S7	S8	S9	S10

C000h	OFF	OFF	ON	ON

D000h	OFF	OFF	ON	OFF

Cabling for this Adapter

Thin Ethernet via BNC Connector


SMC ARCNET PC130-E Card
SMC ARCNET PC130-E

This is the SMC ARCNET PC130 E Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

J2	J3	J4	J5	J7

IRQ2	ON	OFF	OFF	OFF	OFF

IRQ3	OFF	ON	OFF	OFF	OFF

IRQ4	OFF	OFF	ON	OFF	OFF

IRQ5	OFF	OFF	OFF	ON	OFF

IRQ7	OFF	OFF	OFF	OFF	ON

Base I/O Address

SW1

S1	S2	S3

260h	ON	ON	ON

290h	ON	ON	OFF

2E0h	ON	OFF	ON

2F0h	ON	OFF	OFF

300h	OFF	ON	ON

350h	OFF	ON	OFF

380h	OFF	OFF	ON

3E0h	OFF	OFF	OFF

Base Memory Address

SW1

S4	S5	S6	S7	S8

C000h	ON	ON	ON	ON	ON

D000h	ON	OFF	OFF	ON	ON

Cabling for this Adapter

Thin Ethernet via BNC Connector


SMC ARCNET PC220-120 Card
SMC ARCNET PC220-120

This is the SMC ARCNET PC220-120 Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

J2	J3	J4	J5	J7

IRQ2	ON	OFF	OFF	OFF	OFF

IRQ3	OFF	ON	OFF	OFF	OFF

IRQ4	OFF	OFF	ON	OFF	OFF

IRQ5	OFF	OFF	OFF	ON	OFF

IRQ7	OFF	OFF	OFF	OFF	ON

Base I/O Address

SW2

S1	S2	S3	S4	S5	S6

200h	OFF	ON	ON	ON	ON	ON

210h	OFF	ON	ON	ON	ON	OFF

220h	OFF	ON	ON	ON	OFF	ON

230h	OFF	ON	ON	ON	OFF	OFF

240h	OFF	ON	ON	OFF	ON	ON

250h	OFF	ON	ON	OFF	ON	OFF

260h	OFF	ON	ON	OFF	OFF	ON

270h	OFF	ON	ON	OFF	OFF	OFF

280h	OFF	ON	OFF	ON	ON	ON

290h	OFF	ON	OFF	ON	ON	OFF

2A0h	OFF	ON	OFF	ON	OFF	ON

2B0h	OFF	ON	OFF	ON	OFF	OFF

2C0h	OFF	ON	OFF	OFF	ON	ON

2D0h	OFF	ON	OFF	OFF	ON	OFF

2E0h	OFF	ON	OFF	OFF	OFF	ON

2F0h	OFF	ON	OFF	OFF	OFF	OFF

300h	OFF	OFF	ON	ON	ON	ON

310h	OFF	OFF	ON	ON	ON	OFF

320h	OFF	OFF	ON	ON	OFF	ON

330h	OFF	OFF	ON	ON	OFF	OFF

340h	OFF	OFF	ON	OFF	ON	ON

350h	OFF	OFF	ON	OFF	ON	OFF

360h	OFF	OFF	ON	OFF	OFF	ON

370h	OFF	OFF	ON	OFF	OFF	OFF

380h	OFF	OFF	OFF	ON	ON	ON

390h	OFF	OFF	OFF	ON	ON	OFF

3A0h	OFF	OFF	OFF	ON	OFF	ON

3B0h	OFF	OFF	OFF	ON	OFF	OFF

3C0h	OFF	OFF	OFF	OFF	ON	ON

3D0h	OFF	OFF	OFF	OFF	ON	OFF

3E0h	OFF	OFF	OFF	OFF	OFF	ON

3F0h	OFF	OFF	OFF	OFF	OFF	OFF

Base Memory Address

SW3

S1	S2	S3	S4	S5	S6	S7	S8

C000h	OFF	OFF	ON	ON	ON	ON	ON	ON

C800h	OFF	OFF	ON	ON	OFF	ON	ON	ON

D000h	OFF	OFF	ON	OFF	ON	ON	ON	ON

Cabling for this Adapter

Thin Ethernet via BNC Connector


SMC ARCNET PC270-E Card
SMC ARCNET PC270-E

This is the SMC ARCNET PC270-E Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

J2	J3	J4	J5	J7

IRQ2	ON	OFF	OFF	OFF	OFF

IRQ3	OFF	ON	OFF	OFF	OFF

IRQ4	OFF	OFF	ON	OFF	OFF

IRQ5	OFF	OFF	OFF	ON	OFF

IRQ7	OFF	OFF	OFF	OFF	ON

Base I/O Address

SW1

S1	S2	S3

260h	ON	ON	ON

290h	ON	ON	OFF

2E0h	ON	OFF	ON

2F0h	ON	OFF	OFF

300h	OFF	ON	ON

350h	OFF	ON	OFF

380h	OFF	OFF	ON

3E0h	OFF	OFF	OFF

Base Memory Address

SW1

S4	S5	S6	S7	S8

C000h	ON	ON	ON	ON	ON

D000h	ON	OFF	OFF	ON	ON

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector


SMC ARCNET PC500 Card
SMC ARCNET PC500

This is the SMC ARCNET PC500 Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

SW1

S7	S8	S9	S10

IRQ3	OFF	OFF	ON	ON

IRQ4	ON	ON	OFF	ON

IRQ5	OFF	ON	OFF	ON

IRQ7	OFF	OFF	OFF	ON

IRQ9	OFF	ON	ON	OFF

IRQ10	ON	OFF	ON	OFF

IRQ11	OFF	OFF	ON	OFF

IRQ12	ON	ON	OFF	OFF

Base I/O Address

SW1

S1	S2	S3	S4	S5	S6

200h	ON	ON	ON	ON	ON	OFF

210h	OFF	ON	ON	ON	ON	OFF

220h	ON	OFF	ON	ON	ON	OFF

230h	OFF	OFF	ON	ON	ON	OFF

240h	ON	ON	OFF	ON	ON	OFF

250h	OFF	ON	OFF	ON	ON	OFF

260h	ON	OFF	OFF	ON	ON	OFF

270h	OFF	OFF	OFF	ON	ON	OFF

280h	ON	ON	ON	OFF	ON	OFF

290h	OFF	ON	ON	OFF	ON	OFF

2A0h	ON	OFF	ON	OFF	ON	OFF

2B0h	OFF	OFF	ON	OFF	ON	OFF

2C0h	ON	ON	OFF	OFF	ON	OFF

2D0h	OFF	ON	OFF	OFF	ON	OFF

2E0h	ON	OFF	OFF	OFF	ON	OFF

2F0h	OFF	OFF	OFF	OFF	ON	OFF

300h	ON	ON	ON	ON	OFF	OFF

310h	OFF	ON	ON	ON	OFF	OFF

320h	ON	OFF	ON	ON	OFF	OFF

330h	OFF	OFF	ON	ON	OFF	OFF

340h	ON	ON	OFF	ON	OFF	OFF

350h	OFF	ON	OFF	ON	OFF	OFF

360h	ON	OFF	OFF	ON	OFF	OFF

370h	OFF	OFF	OFF	ON	OFF	OFF

380h	ON	ON	ON	OFF	OFF	OFF

390h	OFF	ON	ON	OFF	OFF	OFF

3A0h	ON	OFF	ON	OFF	OFF	OFF

3B0h	OFF	OFF	ON	OFF	OFF	OFF

3C0h	ON	ON	OFF	OFF	OFF	OFF

3D0h	OFF	ON	OFF	OFF	OFF	OFF

3E0h	ON	OFF	OFF	OFF	OFF	OFF

3F0h	OFF	OFF	OFF	OFF	OFF	OFF

Base Memory Address

NOT USED

Cabling for this Adapter

Thin Ethernet via BNC Connector


SMC ARCNET PC550W Card
SMC ARCNET PC550

This is the SMC ARCNET PC550 Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

SW1

S7	S8	S9	S10

IRQ3	OFF	OFF	ON	ON

IRQ4	ON	ON	OFF	ON

IRQ5	OFF	ON	OFF	ON

IRQ7	OFF	OFF	OFF	ON

IRQ9	OFF	ON	ON	OFF

IRQ10	ON	OFF	ON	OFF

IRQ11	OFF	OFF	ON	OFF

IRQ12	ON	ON	OFF	OFF

Base I/O Address

SW1

S1	S2	S3	S4	S5	S6

200h	ON	ON	ON	ON	ON	OFF

210h	OFF	ON	ON	ON	ON	OFF

220h	ON	OFF	ON	ON	ON	OFF

230h	OFF	OFF	ON	ON	ON	OFF

240h	ON	ON	OFF	ON	ON	OFF

250h	OFF	ON	OFF	ON	ON	OFF

260h	ON	OFF	OFF	ON	ON	OFF

270h	OFF	OFF	OFF	ON	ON	OFF

280h	ON	ON	ON	OFF	ON	OFF

290h	OFF	ON	ON	OFF	ON	OFF

2A0h	ON	OFF	ON	OFF	ON	OFF

2B0h	OFF	OFF	ON	OFF	ON	OFF

2C0h	ON	ON	OFF	OFF	ON	OFF

2D0h	OFF	ON	OFF	OFF	ON	OFF

2E0h	ON	OFF	OFF	OFF	ON	OFF

2F0h	OFF	OFF	OFF	OFF	ON	OFF

300h	ON	ON	ON	ON	OFF	OFF

310h	OFF	ON	ON	ON	OFF	OFF

320h	ON	OFF	ON	ON	OFF	OFF

330h	OFF	OFF	ON	ON	OFF	OFF

340h	ON	ON	OFF	ON	OFF	OFF

350h	OFF	ON	OFF	ON	OFF	OFF

360h	ON	OFF	OFF	ON	OFF	OFF

370h	OFF	OFF	OFF	ON	OFF	OFF

380h	ON	ON	ON	OFF	OFF	OFF

390h	OFF	ON	ON	OFF	OFF	OFF

3A0h	ON	OFF	ON	OFF	OFF	OFF

3B0h	OFF	OFF	ON	OFF	OFF	OFF

3C0h	ON	ON	OFF	OFF	OFF	OFF

3D0h	OFF	ON	OFF	OFF	OFF	OFF

3E0h	ON	OFF	OFF	OFF	OFF	OFF

3F0h	OFF	OFF	OFF	OFF	OFF	OFF

Base Memory Address

NOT USED

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector


SMC ARCNET PC600W Card
SMC ARCNET PC600

This is the SMC ARCNET PC600 Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

JP3

J3	J4	J5	J7	J9	J10

IRQ3	ON	OFF	OFF	OFF	OFF	OFF

IRQ4	OFF	ON	OFF	OFF	OFF	OFF

IRQ5	OFF	OFF	ON	OFF	OFF	OFF

IRQ7	OFF	OFF	OFF	ON	OFF	OFF

IRQ9	OFF	OFF	OFF	OFF	ON	OFF

IRQ10	OFF	OFF	OFF	OFF	OFF	ON

Base I/O Address

SW1

S1	S2	S3

260h	ON	ON	ON

290h	ON	ON	OFF

2E0h	ON	OFF	ON

2F0h	ON	OFF	OFF

300h	OFF	ON	ON

350h	OFF	ON	OFF

380h	OFF	OFF	ON

3E0h	OFF	OFF	OFF

Base Memory Address

SW2

S4	S5	S6	S7	S8

C000h	ON	ON	ON	ON	ON

D000h	ON	OFF	OFF	ON	ON

Cabling for this Adapter

Thin Ethernet via BNC Connector


Thomas Conrad Cards
Thomas Conrad

Windows 95 Adapter help currently includes the following Thomas Conrad network cards:

TC6045

TC6142

TC6145

TC6242

TC6245


TC6045 Card
TC6045

This is the Thomas Conrad TC6045 Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

J14	J15	J12	J11	J10	J3	J4	J5	J6	J7	J9

IRQ3	OFF	OFF	OFF	OFF	OFF	ON	OFF	OFF	OFF	OFF	OFF

IRQ4	OFF	OFF	OFF	OFF	OFF	OFF	ON	OFF	OFF	OFF	OFF

IRQ5	OFF	OFF	OFF	OFF	OFF	OFF	OFF	ON	OFF	OFF	OFF

IRQ6	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF	ON	OFF	OFF

IRQ7	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF	ON	OFF

IRQ9	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF	ON

IRQ10	OFF	OFF	OFF	OFF	ON	OFF	OFF	OFF	OFF	OFF	OFF

IRQ11	OFF	OFF	OFF	ON	OFF	OFF	OFF	OFF	OFF	OFF	OFF

IRQ12	OFF	OFF	ON	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF

IRQ14	ON	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF

IRQ15	OFF	ON	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF

Base I/O Address

SW3

S3	S4	S5	S6	S7	S8

2E0h	OFF	ON	OFF	OFF	OFF	ON

2F0h	OFF	ON	OFF	OFF	OFF	OFF

300h	OFF	OFF	ON	ON	ON	ON

350h	OFF	OFF	ON	OFF	ON	OFF

Base Memory Address

SW1	SW3

S1	S2	S3	S4	S5	S6	S7	S8	S1	S2

C000h	ON	ON	ON	ON	OFF	OFF	ON	ON	ON	ON

C400h	ON	ON	ON	ON	OFF	OFF	ON	ON	ON	OFF

C800h	ON	ON	ON	ON	OFF	OFF	ON	ON	OFF	ON

CC00h	ON	ON	ON	ON	OFF	OFF	ON	ON	OFF	OFF

D000h	ON	ON	ON	ON	OFF	OFF	ON	OFF	ON	ON

D400h	ON	ON	ON	ON	OFF	OFF	ON	OFF	ON	OFF

D800h	ON	ON	ON	ON	OFF	OFF	ON	OFF	OFF	ON

DC00h	ON	ON	ON	ON	OFF	OFF	ON	OFF	OFF	OFF

Cabling for this Adapter

Thin Ethernet via BNC Connector


TC6142 Card
TC6142

This is the Thomas Conrad TC6142 Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

J3	J4	J5	J7	J2

IRQ2	OFF	OFF	OFF	OFF	ON

IRQ3	ON	OFF	OFF	OFF	OFF

IRQ4	OFF	ON	OFF	OFF	OFF

IRQ5	OFF	OFF	ON	OFF	OFF

IRQ7	OFF	OFF	OFF	ON	OFF

Base I/O Address

SW3

S3	S4	S5	S6	S7	S8

2E0h	OFF	ON	OFF	OFF	OFF	ON

2F0h	OFF	ON	OFF	OFF	OFF	OFF

300h	OFF	OFF	ON	ON	ON	ON

350h	OFF	OFF	ON	OFF	ON	OFF

Base Memory Address

SW1

S1	S2	S3	S4	S5	S6

C000h	OFF	OFF	ON	ON	ON	ON

C400h	OFF	OFF	ON	ON	ON	OFF

C800h	OFF	OFF	ON	ON	OFF	ON

CC00h	OFF	OFF	ON	ON	OFF	OFF

D000h	OFF	OFF	ON	OFF	ON	ON

D400h	OFF	OFF	ON	OFF	ON	OFF

D800h	OFF	OFF	ON	OFF	OFF	ON

DC00h	OFF	OFF	ON	OFF	OFF	OFF

Cabling for this Adapter

Thin Ethernet via BNC Connector


TC6145 Card
TC6145

This is the Thomas Conrad TC6145 Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

J14	J15	J12	J11	J10	J3	J4	J5	J6	J7	J9

IRQ3	OFF	OFF	OFF	OFF	OFF	ON	OFF	OFF	OFF	OFF	OFF

IRQ4	OFF	OFF	OFF	OFF	OFF	OFF	ON	OFF	OFF	OFF	OFF

IRQ5	OFF	OFF	OFF	OFF	OFF	OFF	OFF	ON	OFF	OFF	OFF

IRQ6	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF	ON	OFF	OFF

IRQ7	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF	ON	OFF

IRQ9	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF	ON

IRQ10	OFF	OFF	OFF	OFF	ON	OFF	OFF	OFF	OFF	OFF	OFF

IRQ11	OFF	OFF	OFF	ON	OFF	OFF	OFF	OFF	OFF	OFF	OFF

IRQ12	OFF	OFF	ON	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF

IRQ14	ON	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF

IRQ15	OFF	ON	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF

Base I/O Address

SW3

S3	S4	S5	S6	S7	S8

2E0h	OFF	ON	OFF	OFF	OFF	ON

2F0h	OFF	ON	OFF	OFF	OFF	OFF

300h	OFF	OFF	ON	ON	ON	ON

350h	OFF	OFF	ON	OFF	ON	OFF

Base Memory Address

SW1	SW3

S1	S2	S3	S4	S5	S6	S7	S8	S1	S2

C000h	ON	ON	ON	ON	OFF	OFF	ON	ON	ON	ON

C400h	ON	ON	ON	ON	OFF	OFF	ON	ON	ON	OFF

C800h	ON	ON	ON	ON	OFF	OFF	ON	ON	OFF	ON

CC00h	ON	ON	ON	ON	OFF	OFF	ON	ON	OFF	OFF

D000h	ON	ON	ON	ON	OFF	OFF	ON	OFF	ON	ON

D400h	ON	ON	ON	ON	OFF	OFF	ON	OFF	ON	OFF

D800h	ON	ON	ON	ON	OFF	OFF	ON	OFF	OFF	ON

DC00h	ON	ON	ON	ON	OFF	OFF	ON	OFF	OFF	OFF

Cabling for this Adapter

Thin Ethernet via BNC Connector


TC6242 Card
TC6242

This is the Thomas Conrad TC6242 Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

J3	J4	J5	J7	J2

IRQ2	OFF	OFF	OFF	OFF	ON

IRQ3	ON	OFF	OFF	OFF	OFF

IRQ4	OFF	ON	OFF	OFF	OFF

IRQ5	OFF	OFF	ON	OFF	OFF

IRQ7	OFF	OFF	OFF	ON	OFF

Base I/O Address

SW3

S3	S4	S5	S6	S7	S8

2E0h	OFF	ON	OFF	OFF	OFF	ON

2F0h	OFF	ON	OFF	OFF	OFF	OFF

300h	OFF	OFF	ON	ON	ON	ON

350h	OFF	OFF	ON	OFF	ON	OFF

Base Memory Address

SW1

S1	S2	S3	S4	S5	S6

C000h	OFF	OFF	ON	ON	ON	ON

C400h	OFF	OFF	ON	ON	ON	OFF

C800h	OFF	OFF	ON	ON	OFF	ON

CC00h	OFF	OFF	ON	ON	OFF	OFF

D000h	OFF	OFF	ON	OFF	ON	ON

D400h	OFF	OFF	ON	OFF	ON	OFF

D800h	OFF	OFF	ON	OFF	OFF	ON

DC00h	OFF	OFF	ON	OFF	OFF	OFF

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector

Thin Ethernet via BNC Connector


TC6245 Card
TC6245

This is the Thomas Conrad TC6245 Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

J14	J15	J13	J11	J10	J3	J4	J5	J6	J7	J9

IRQ3	OFF	OFF	OFF	OFF	OFF	ON	OFF	OFF	OFF	OFF	OFF

IRQ4	OFF	OFF	OFF	OFF	OFF	OFF	ON	OFF	OFF	OFF	OFF

IRQ5	OFF	OFF	OFF	OFF	OFF	OFF	OFF	ON	OFF	OFF	OFF

IRQ6	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF	ON	OFF	OFF

IRQ7	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF	ON	OFF

IRQ9	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF	ON

IRQ10	OFF	OFF	OFF	OFF	ON	OFF	OFF	OFF	OFF	OFF	OFF

IRQ11	OFF	OFF	OFF	ON	OFF	OFF	OFF	OFF	OFF	OFF	OFF

IRQ13	OFF	OFF	ON	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF

IRQ14	ON	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF

IRQ15	OFF	ON	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF

Base I/O Address

SW3

S3	S4	S5	S6	S7	S8

2E0h	OFF	ON	OFF	OFF	OFF	ON

2F0h	OFF	ON	OFF	OFF	OFF	OFF

380h	OFF	OFF	ON	ON	ON	ON

350h	OFF	OFF	ON	OFF	ON	OFF

Base Memory Address

SW1

S1	S2	S3	S4	S5	S6

C000h	OFF	OFF	ON	ON	ON	ON

C400h	OFF	OFF	ON	ON	ON	OFF

C800h	OFF	OFF	ON	ON	OFF	ON

CC00h	OFF	OFF	ON	ON	OFF	OFF

D000h	OFF	OFF	ON	OFF	ON	ON

D400h	OFF	OFF	ON	OFF	ON	OFF

D800h	OFF	OFF	ON	OFF	OFF	ON

DC00h	OFF	OFF	ON	OFF	OFF	OFF

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector


Toshiba Cards
Toshiba

Windows 95 Adapter help currently includes the following Toshiba network cards:

ToshibaLan Laptop

ToshibaLan Desktop


ToshibaLan Laptop Card
ToshibaLan Laptop

This is the Toshiba ToshibaLan Laptop Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

PJ6

J1-2	J3-4	J5-6	J7-8	J9-10	J11-12

IRQ3	OFF	OFF	OFF	OFF	OFF	ON

IRQ4	OFF	OFF	OFF	OFF	ON	OFF

IRQ5	OFF	OFF	ON	OFF	OFF	OFF

IRQ7	ON	OFF	OFF	OFF	OFF	OFF

IRQ9	OFF	OFF	OFF	ON	OFF	OFF

IRQ10	OFF	ON	OFF	OFF	OFF	OFF

Base I/O Address

SW1

S3	S4	S5	S6

200h	ON	ON	ON	ON

220h	ON	ON	ON	OFF

240h	ON	ON	OFF	ON

260h	ON	ON	OFF	OFF

280h	ON	OFF	ON	ON

2A0h	ON	OFF	ON	OFF

2C0h	ON	OFF	OFF	ON

2E0h	ON	OFF	OFF	OFF

300h	OFF	ON	ON	ON

320h	OFF	ON	ON	OFF

340h	OFF	ON	OFF	ON

360h	OFF	ON	OFF	OFF

380h	OFF	OFF	ON	ON

3A0h	OFF	OFF	ON	OFF

3C0h	OFF	OFF	OFF	ON

3E0h	OFF	OFF	OFF	OFF

Base Memory Address

SOFTWARE CONFIGURABLE

Cabling for this Adapter

Thick Ethernet via AUI Connector

Thin Ethernet via BNC Connector


ToshibaLan Desktop Card
ToshibaLan Desktop

This is the Toshiba ToshibaLan Desktop Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

PJ6

J1-2	J3-4	J5-6	J7-8	J9-10	J11-12

IRQ3	OFF	OFF	OFF	OFF	OFF	ON

IRQ4	OFF	OFF	OFF	OFF	ON	OFF

IRQ5	OFF	OFF	ON	OFF	OFF	OFF

IRQ7	ON	OFF	OFF	OFF	OFF	OFF

IRQ9	OFF	OFF	OFF	ON	OFF	OFF

IRQ10	OFF	ON	OFF	OFF	OFF	OFF

Base I/O Address

SW1

S3	S4	S5	S6

200h	ON	ON	ON	ON

220h	ON	ON	ON	OFF

240h	ON	ON	OFF	ON

260h	ON	ON	OFF	OFF

280h	ON	OFF	ON	ON

2A0h	ON	OFF	ON	OFF

2C0h	ON	OFF	OFF	ON

2E0h	ON	OFF	OFF	OFF

300h	OFF	ON	ON	ON

320h	OFF	ON	ON	OFF

340h	OFF	ON	OFF	ON

360h	OFF	ON	OFF	OFF

380h	OFF	OFF	ON	ON

3A0h	OFF	OFF	ON	OFF

3C0h	OFF	OFF	OFF	ON

3E0h	OFF	OFF	OFF	OFF

Base Memory Address

SOFTWARE CONFIGURABLE

Cabling for this Adapter

Thick Ethernet via AUI Connector

Thin Ethernet via BNC Connector


Ungerman Bass Cards
Ungerman Bass (UB)

Windows 95 Adapter help currently includes the following Ungerman Bass network cards:

UB NIUpc

UB NIU ps

UB NIUpc EOTP

UB pcNIU

UB pcNIU ex 128K

UB pcNIU ex 512K

UB Network Adapter/ps

UB NIUpc3270


UB NICps Card
UB Network Adapter/ps

This Network Adapter card can be configured using the software supplied by the manufacturer. Please consult the documentation that came with your Network Adapter or contact the manufacturer of the Network Adapter for further information.


UB NIUpc Card
UB NIUpc

This is the Ungermann-Bass NIUpc Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

E13-E14	E19-E20	E14-E15	E20-E21

IRQ2	ON	OFF	OFF	OFF

IRQ3	OFF	ON	OFF	OFF

IRQ4	OFF	OFF	ON	OFF

IRQ5	OFF	OFF	OFF	ON

Base I/O Address

E22-E23	E23-E24	E25-E26	E26-E27	E31-E32	E32-E33

350h	OFF	ON	OFF	ON	ON	OFF

358h	ON	OFF	OFF	ON	ON	OFF

360h	OFF	ON	ON	OFF	OFF	ON

368h	ON	OFF	ON	OFF	OFF	ON

Base Memory Address

E10-E11	E11-E12	E16-E17	E17-E18	E28-E29	E29-E30

8800h	OFF	ON	OFF	ON	OFF	ON

9800h	ON	OFF	OFF	ON	OFF	ON

A800h	OFF	ON	ON	OFF	OFF	ON

B800h	ON	OFF	ON	OFF	OFF	ON

C800h	OFF	ON	OFF	ON	ON	OFF

D800h	ON	OFF	OFF	ON	ON	OFF

E800h	OFF	ON	ON	OFF	ON	OFF

F800h	ON	OFF	ON	OFF	ON	OFF

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector

Thick Ethernet via AUI Connector


UB NIUpc 3270 Card
UB NIUpc 3270

This is the Ungermann-Bass NIUpc3270 Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

E13-E14	E19-E20	E14-E15	E20-E21

IRQ2	ON	OFF	OFF	OFF

IRQ3	OFF	ON	OFF	OFF

IRQ4	OFF	OFF	ON	OFF

IRQ5	OFF	OFF	OFF	ON

Base I/O Address

E22-E23	E23-E24	E25-E26	E26-E27	E31-E32	E32-E33

350h	OFF	ON	OFF	ON	ON	OFF

358h	ON	OFF	OFF	ON	ON	OFF

360h	OFF	ON	ON	OFF	OFF	ON

368h	ON	OFF	ON	OFF	OFF	ON

Base Memory Address

E10-E11	E11-E12	E16-E17	E17-E18	E28-E29	E29-E30

8800h	OFF	ON	OFF	ON	OFF	ON

9800h	ON	OFF	OFF	ON	OFF	ON

A800h	OFF	ON	ON	OFF	OFF	ON

B800h	ON	OFF	ON	OFF	OFF	ON

C800h	OFF	ON	OFF	ON	ON	OFF

D800h	ON	OFF	OFF	ON	ON	OFF

E800h	OFF	ON	ON	OFF	ON	OFF

F800h	ON	OFF	ON	OFF	ON	OFF

Cabling for this Adapter

Unshielded Twisted Pair via RJ-45 Connector

Thick Ethernet via AUI Connector


UB NIUpc EOTP Card
UB NIUpc EOTP

This is the Ungermann-Bass NIUpc EOTP Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

SOFTWARE CONFIGURABLE

Base I/O Address

E11-E12	E13-E14

350h	ON	ON

358h	OFF	ON

360h	ON	OFF

368h	OFF	OFF

Base Memory Address

SOFTWARE CONFIGURABLE

TP/AUI

1	2	3

TP	ON	ON	OFF

AUI	OFF	ON	ON

Cabling for this Adapter

Thick Ethernet via AUI Connector

Unshielded Twisted Pair via RJ-45 Connector


UB NIU ps Card
UB NIU ps

This Network Adapter card is configured using the 'Reference Disk' provided with your Micro-Channel System.  For further information consult the documentation provided with the Network Adapter or contact your vendor.

Cabling for this Adapter

For Token-Ring, Shielded Twisted Pair (IBM Type 1) via DB-9 Connector

For Ethernet, Thick Ethernet via AUI Connector


UB pcNIU Card
UB pcNIU

This is the Ungermann-Bass pcNIU Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

E19-E20	E20-E21

IRQ2	OFF	ON

IRQ5	ON	OFF

Base I/O Address

E1-E2	E2-E3

360h	ON	OFF

368h	OFF	ON

Base Memory Address

E4-E5	E5-E6	E7-E8	E8-E9	E10-E11	E11-E12	E13-E14	E14-E15

8000h	OFF	ON	ON	OFF	ON	OFF	ON	OFF

9000h	OFF	ON	ON	OFF	ON	OFF	OFF	ON

A000h	OFF	ON	ON	OFF	OFF	ON	ON	OFF

B000h	OFF	ON	ON	OFF	OFF	ON	OFF	ON

C000h	OFF	ON	OFF	ON	ON	OFF	ON	OFF

D000h	OFF	ON	OFF	ON	ON	OFF	OFF	ON

E000h	OFF	ON	OFF	ON	OFF	ON	ON	OFF

F000h	OFF	ON	OFF	ON	OFF	ON	OFF	ON

Cabling for this Adapter

Thick Ethernet via AUI Connector


UB pcNIU ex 128K Card
UB pcNIU ex 128K

This is the Ungermann-Bass pcNIU ex 128K Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

J2	J3	J4	J5

IRQ2	ON	OFF	OFF	OFF

IRQ3	OFF	ON	OFF	OFF

IRQ4	OFF	OFF	ON	OFF

IRQ5	OFF	OFF	OFF	ON

Base I/O Address

E1-E2	E2-E3

360h	OFF	ON

368h	ON	OFF

Base Memory Address (32K WINDOW)

E4-E5	E5-E6	E7-E8	E8-E9	E10-E11	E11-E12	E13-E14	E14-E15

8000h	OFF	ON	OFF	ON	OFF	ON	OFF	ON

8800h	OFF	ON	OFF	ON	OFF	ON	ON	OFF

9000h	OFF	ON	OFF	ON	ON	OFF	OFF	ON

9800h	OFF	ON	OFF	ON	ON	OFF	ON	OFF

A000h	OFF	ON	ON	OFF	OFF	ON	OFF	ON

A800h	OFF	ON	ON	OFF	OFF	ON	ON	OFF

B000h	OFF	ON	ON	OFF	ON	OFF	OFF	ON

B800h	OFF	ON	ON	OFF	ON	OFF	ON	OFF

C000h	ON	OFF	OFF	ON	OFF	ON	OFF	ON

C800h	ON	OFF	OFF	ON	OFF	ON	ON	OFF

D000h	ON	OFF	OFF	ON	ON	OFF	OFF	ON

D800h	ON	OFF	OFF	ON	ON	OFF	ON	OFF

E000h	ON	OFF	ON	OFF	OFF	ON	OFF	ON

E800h	ON	OFF	ON	OFF	OFF	ON	ON	OFF

F000h	ON	OFF	ON	OFF	ON	OFF	OFF	ON

F800h	ON	OFF	ON	OFF	ON	OFF	ON	OFF

Base Memory Address (64K WINDOW)

E4-E5	E5-E6	E7-E8	E8-E9	E10-E11	E11-E12	E13-E14	E14-E15

8000h	OFF	ON	OFF	ON	OFF	ON	OFF	OFF

9000h	OFF	ON	OFF	ON	ON	OFF	OFF	OFF

A000h	OFF	ON	ON	OFF	OFF	ON	OFF	OFF

B000h	OFF	ON	ON	OFF	ON	OFF	OFF	OFF

C000h	ON	OFF	OFF	ON	OFF	ON	OFF	OFF

D000h	ON	OFF	OFF	ON	ON	OFF	OFF	OFF

E000h	ON	OFF	ON	OFF	OFF	ON	OFF	OFF

F000h	ON	OFF	ON	OFF	ON	OFF	OFF	OFF

Cabling for this Adapter

Thick Ethernet via AUI Connector


UB pcNIU ex 512K Card
UB pcNIU ex 512K

This is the Ungermann-Bass pcNIU ex 512K Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

J2	J3	J4	J5

IRQ2	ON	OFF	OFF	OFF

IRQ3	OFF	ON	OFF	OFF

IRQ4	OFF	OFF	ON	OFF

IRQ5	OFF	OFF	OFF	ON

Base I/O Address

E1-E2	E2-E3

360h	OFF	ON

368h	ON	OFF

Base Memory Address (32K WINDOW)

E4-E5	E5-E6	E7-E8	E8-E9	E10-E11	E11-E12	E13-E14	E14-E15

8000h	OFF	ON	OFF	ON	OFF	ON	OFF	ON

8800h	OFF	ON	OFF	ON	OFF	ON	ON	OFF

9000h	OFF	ON	OFF	ON	ON	OFF	OFF	ON

9800h	OFF	ON	OFF	ON	ON	OFF	ON	OFF

A000h	OFF	ON	ON	OFF	OFF	ON	OFF	ON

A800h	OFF	ON	ON	OFF	OFF	ON	ON	OFF

B000h	OFF	ON	ON	OFF	ON	OFF	OFF	ON

B800h	OFF	ON	ON	OFF	ON	OFF	ON	OFF

C000h	ON	OFF	OFF	ON	OFF	ON	OFF	ON

C800h	ON	OFF	OFF	ON	OFF	ON	ON	OFF

D000h	ON	OFF	OFF	ON	ON	OFF	OFF	ON

D800h	ON	OFF	OFF	ON	ON	OFF	ON	OFF

E000h	ON	OFF	ON	OFF	OFF	ON	OFF	ON

E800h	ON	OFF	ON	OFF	OFF	ON	ON	OFF

F000h	ON	OFF	ON	OFF	ON	OFF	OFF	ON

F800h	ON	OFF	ON	OFF	ON	OFF	ON	OFF

Base Memory Address (64K WINDOW)

E4-E5	E5-E6	E7-E8	E8-E9	E10-E11	E11-E12	E13-E14	E14-E15

8000h	OFF	ON	OFF	ON	OFF	ON	OFF	OFF

9000h	OFF	ON	OFF	ON	ON	OFF	OFF	OFF

A000h	OFF	ON	ON	OFF	OFF	ON	OFF	OFF

B000h	OFF	ON	ON	OFF	ON	OFF	OFF	OFF

C000h	ON	OFF	OFF	ON	OFF	ON	OFF	OFF

D000h	ON	OFF	OFF	ON	ON	OFF	OFF	OFF

E000h	ON	OFF	ON	OFF	OFF	ON	OFF	OFF

F000h	ON	OFF	ON	OFF	ON	OFF	OFF	OFF

Cabling for this Adapter

Thick Ethernet via AUI Connector


SMC (WD) Cards
SMC (WD)

Windows 95 Adapter help currently includes the following SMC (WD) network cards:

SMC (WD) EtherCard PLUS

SMC (WD) EtherCard PLUS 10T/A for MicroChannel

SMC (WD) EtherCard PLUS/A for MicroChannel

SMC (WD) EtherCard PLUS Elite 16 for MicroChannel

SMC (WD) EtherCard PLUS Elite

SMC (WD) EtherCard PLUS Elite 16

SMC (WD) EtherCard PLUS Elite 16T

SMC (WD) EtherCard PLUS Elite 16 Combo


SMC (WD) EtherCard PLUS

This is the SMC (WD) EtherCard PLUS Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

W2

J1	J2	J3	J4	J5	J6

IRQ2	OFF	OFF	OFF	OFF	OFF	ON

IRQ3	OFF	OFF	OFF	OFF	ON	OFF

IRQ4	OFF	OFF	OFF	ON	OFF	OFF

IRQ5	OFF	OFF	ON	OFF	OFF	OFF

IRQ6	OFF	ON	OFF	OFF	OFF	OFF

IRQ7	ON	OFF	OFF	OFF	OFF	OFF

Base I/O Address

W1

J1	J2	J3	J4

200h	ON	ON	ON	ON

220h	OFF	ON	ON	ON

240h	ON	OFF	ON	ON

260h	OFF	OFF	ON	ON

280h	ON	ON	OFF	ON

2A0h	OFF	ON	OFF	ON

2C0h	ON	OFF	OFF	ON

2E0h	OFF	OFF	OFF	ON

300h	ON	ON	ON	OFF

320h	OFF	ON	ON	OFF

340h	ON	OFF	ON	OFF

360h	OFF	OFF	ON	OFF

380h	ON	ON	OFF	OFF

3A0h	OFF	ON	OFF	OFF

3C0h	ON	OFF	OFF	OFF

3E0h	OFF	OFF	OFF	OFF

Base Memory Address

SOFTWARE CONFIGURABLE

Default - C400h

Cabling for this Adapter

Thick Ethernet via AUI Connector

Thin Ethernet via BNC Connector


SMC (WD) EtherCard PLUS 10T/A for MicroChannel Carrd
SMC (WD) EtherCard PLUS 10T/A for MicroChannel

This Network Adapter card is configured using the 'Reference Disk' provided with your Micro-Channel System.  For further information consult the documentation provided with the Network Adapter or contact your vendor.

Cabling for this Adapter

Thick Ethernet via AUI Connector

Unshielded Twisted Pair via RJ-45 Connector


SMC (WD) EtherCard PLUS/A for MicroChannel Carrd
SMC (WD) EtherCard PLUS/A for MicroChannel

This Network Adapter card is configured using the 'Reference Disk' provided with your Micro-Channel System.  For further information consult the documentation provided with the Network Adapter or contact your vendor.

Cabling for this Adapter

Thick Ethernet via AUI Connector

Thin Ethernet via BNC Connector


SMC (WD) EtherCard PLUS Elite 16 for MicroChannel Carrd
SMC (WD) EtherCard PLUS Elite 16 for MicroChannel

This Network Adapter card is configured using the 'Reference Disk' provided with your Micro-Channel System.  For further information consult the documentation provided with the Network Adapter or contact your vendor.

Cabling for this Adapter

Thick Ethernet via AUI Connector

Thin Ethernet via BNC Connector


SMC (WD) EtherCard PLUS Elite Carrd
SMC (WD) EtherCard PLUS Elite

This is the SMC (WD) EtherCard PLUS Elite Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

W1

J1	J2	J3

SOFT	ON	OFF	OFF

IRQ3	OFF	ON	OFF

IRQ5	OFF	OFF	ON

Base I/O Address

W1

J1	J2	J3

SOFT	ON	OFF	OFF

280h	OFF	ON	OFF

300h	OFF	OFF	ON

Base Memory Address

W1

J1	J2	J3

SOFT	ON	OFF	OFF

D000h	OFF	ON	OFF

CA00h	OFF	OFF	ON

Cabling for this Adapter

Thick Ethernet via AUI Connector

Thin Ethernet via BNC Connector


SMC (WD) EtherCard PLUS Elite 16 Carrd
SMC (WD) EtherCard PLUS Elite 16

This is the SMC (WD) EtherCard PLUS Elite 16 Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

W1

J1	J2	J3

SOFT	ON	OFF	OFF

IRQ3	OFF	ON	OFF

IRQ10	OFF	OFF	ON

Base I/O Address

W1

J1	J2	J3

SOFT	ON	OFF	OFF

280h	OFF	ON	OFF

300h	OFF	OFF	ON

Base Memory Address

W1

J1	J2	J3

SOFT	ON	OFF	OFF

D000h	OFF	ON	OFF

C000h	OFF	OFF	ON

Cabling for this Adapter

Thick Ethernet via AUI Connector

Thin Ethernet via BNC Connector


SMC (WD) EtherCard PLUS Elite 16T Carrd
SMC (WD) EtherCard PLUS Elite 16T

This is the SMC (WD) EtherCard PLUS Elite 16T Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

W1

J1	J2	J3

SOFT	ON	OFF	OFF

IRQ3	OFF	ON	OFF

IRQ10	OFF	OFF	ON

Base I/O Address

W1

J1	J2	J3

SOFT	ON	OFF	OFF

280h	OFF	ON	OFF

300h	OFF	OFF	ON

Base Memory Address

W1

J1	J2	J3

SOFT	ON	OFF	OFF

D000h	OFF	ON	OFF

C000h	OFF	OFF	ON

Cabling for this Adapter

Thick Ethernet via AUI Connector

Unshielded Twisted Pair via RJ-45 Connector


SMC (WD) EtherCard PLUS Elite 16 Combo Carrd
SMC (WD) EtherCard PLUS Elite 16 Combo

This is the SMC (WD) EtherCard PLUS Elite 16 Combo Network Adapter card shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, and Base Memory Address jumper/switch configurations:

Interrupt Request Line (IRQ)

W1

J1	J2	J3

SOFTWARE	ON	OFF	OFF

IRQ3	OFF	ON	OFF

IRQ10	OFF	OFF	ON

Base I/O Address

W1

J1	J2	J3

SOFTWARE	ON	OFF	OFF

280h	OFF	ON	OFF

300h	OFF	OFF	ON

Base Memory Address

W1

J1	J2	J3

SOFTWARE	ON	OFF	OFF

D000h	OFF	ON	OFF

C000h	OFF	OFF	ON

Cabling for this Adapter

Thick Ethernet via AUI Connector

Thin Ethernet via BNC Connector

Unshielded Twisted Pair via RJ-45 Connector


Close!


Closer!


About
About The Great Team That Wrote The Windows '95 Adapter Helpfile

David Conner	All Artwork, Design, & Tireless error checking

Original Team Members (from WFWG 3.1):

Ed Hubbard	Original Design and putting it all together

Lance Craig	Original Network Card Settings

Ryan Battle	Original Defaults & Backup

Special Thanks to:

John Gilbert	Constant Beta Testing (Finding Errors)

Microsoft Press	Definitions and Connector Illustrations

Cliff Schommer	SCSI Type Table

Calvin Mackey	Help with the Word Macros

PSS East Windows 95 Beta Team

Joe Tuck	Charles Teague

Faron Faulk	Lex Thomas

Henry Gray	Rich Thomasson


Direct Memory Access (DMA)

Memory access that does not involve the microprocessor, frequently employed for data transfer directly between memory and an "intelligent' peripheral device such as a disk drive.


Interrupt Request Line (IRQ)

Hardware lines over which devices such as input/output ports, the keyboard, and disk drives can send interrupts (requests for service) to the microprocessor.  Interrupt request lines are assigned different levels of priority so that the microprocessor can determine the relative importance of incoming service requests.

Hardware Interrupt Chart

IRQ	80286 and Above

0	System Timer

1	Keyboard

2	Gateway from IRQ 8-15 (Tie to IRQ 9)

3	COM2:, COM4:

4	COM1:, COM3:

5	Open, (LPT2: on IBM PC/AT)

6	Floppy Disk Controller

7	LPT1:, LPT2:, LPT3:, (LPT1 on IBM PC/AT)

8	Real Time Clock

9	Test link to IRQ 2

10	Open

11	Open

12	PS/2 type mouse port

13	Math Co-Processor

14	Hard Disk Controller

15	Open


RAM Base Address

In relation to memory locations, the portion of a two-part address that remains constant and provides a reference point, or base, from which the location of a byte of data can be calculated.  A base address is accompanied by an offset value that is added to the base to determine the exact location (the absolute address) of the information.  The concept is similar to a street address system and to the Dewey decimal system.  For example, 2010 Main Street consists of a base (the 2000 block of Main Street) plus an offset (10 from the beginning); the book number PB 587 in the Dewey decimal system consists of a base (the subject PB, which indicates the psychology section of a library) and an offset (the number 587, which is the location of the book in the section).  Base addresses are known as segment addresses in IBM and compatible computers.  Data in these computers is identified by its position as a relative offset from the start of the segment.


SCSI
SCSI (Small Computer System Interface)

Pronounced 'scuzzy'; acronym for small computer system interface, a standard high-speed parallel interface defined by the X3T9.2 committee of the American National Standards Institute (ANSI).  A SCSI Host Adapter is used for connecting microcomputers to peripheral devices, such as hard disks and printers, and other computers and local area networks.  Up to seven devices, not including the computer, can be attached through a single SCSI connection (port) through sequential connections called a daisy chain.  Each device has an address (priority number).  Only one device at a time can transmit through the port; priority is given to the device with the highest address.


COAX
COAX Cable


Serial Connectors


SCSI Types

Standard	Byte Width	Bit Width	Cable Name	Pin Count	Max Transfer MByte/sec	Max SCSI Devices	Description
SCSI - 1	1	8	A	50	5	8	Synchronous
SCSI - 2	1	8	A	50	10	8	Fast
SCSI - 2	2	16	A + B	50 + 68	20	8	Fast & Wide (Two cables)
SCSI - 2	4	32	A + B	50 + 68	40	8	Fast & Wide (Two cables)
SCSI - 3	1	8	A	50	10	8	Fast
SCSI - 3	2	16	P	68	20	16	Fast & Wide
SCSI - 3	4	32	P + Q	68 + 68	40	32	Fast & Wide (Two cables)

Single-Ended  and Differential

There are two different ways a SCSI bus can be terminated.  The most common way is by implementing the Single-Ended method.  Single-Ended termination is putting terminators on both ends of the SCSI bus.  Most controller boards on the market today use this method.  The other method is Differential termination.  With Differential termination the device itself is terminated and the SCSI bus isn't terminated.

SCSI - 1

Supports General, Direct Access, Sequential Access, Printer, Write Once, and Processor devices.

SCSI - 2

Supports all of  SCSI - 1 devices and the following:  CD-ROM, Scanner, Optical Memory, Medium Changer, and Communications.

SCSI - 3

Supports all of the SCSI - 1 and SCSI - 2, with the addition of being modular.  Any new technology will be able to make use of this interface.


SCSI Connectors

Low Density Shielded SCSI Connector

Low Density Unshielded SCSI Connector

High Density Shielded SCSI Connector

High Density Unshielded SCSI Connector


SCSI - Low Density Shielded Connector
Low Density Shielded SCSI Connector


SCSI - Low Density UnShielded Connector
Low Density Unshielded SCSI Connector


SCSI - High Density Shielded Connector
High Density Shielded SCSI Connector


SCSI - High Density Unshielded Connector
High Density Unshielded SCSI Connector


Always Cards
Always

Windows 95 Adapter help currently includes the following Always SCSI interface cards:

Always IN-2000


Always IN-2000 Card
Always IN-2000

This is the Always IN-2000 SCSI adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base Memory Address, and other jumper/switch configurations:

SW1

Segment

Address	S1	S2

C800h-CBFFh	OFF	OFF

D800h-DBFFh	ON	OFF

D000h-D3FFh	OFF	ON

Bios Enabled	ON	ON

I/O Port

Address	S3	S4

220h-22Fh	OFF	OFF

200h-20Fh	ON	OFF

110h-11Fh	OFF	ON

100h-10Fh	ON	ON

Interrupt	S5	S6	S7

15	OFF	OFF	OFF

14	OFF	ON	OFF

11	OFF	OFF	ON

10	OFF	ON	ON

Disabled	ON	-	-

Dos 5.0

Support	ON	ON	ON

Synch/Asynch

Operations	S8

Asynchronous	OFF

Synchronous	ON

Floppy

Controller	S9

Disable	OFF

Enable	ON


Adaptech Cards
Adaptec

Windows 95 Adapter help currently includes the following Adaptec SCSI interface cards:

Adaptec 1510

Adaptec 1505

Adaptec 1515

Adaptec 1520A/1522A

Adaptec 1520/1522

Adaptec 1540

Adaptec 1540A

Adaptec 1540B/1542B

Adaptec 1540C/1542C

Adaptec 1640

Adaptec 1740/1744

Adaptec 1740(A)/1744(A)

Adaptec 2740/2740W

Adaptec 2940

Adaptec 2940W


Adaptec 2940W

This is the Adaptec 2940W SCSI adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base Memory Address, and other jumper/switch configurations:


Adaptec 2940

This is the Adaptec 2940 SCSI adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base Memory Address, and other jumper/switch configurations:


Adaptec 2740
Adaptec 2740/2740W

This is the Adaptec 2740/2740W SCSI adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base Memory Address, and other jumper/switch configurations:


Adaptec 1515

This is the Adaptec 1515 SCSI adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base Memory Address, and other jumper/switch configurations:

BIOS Address

Jumper Block J1

Pin 6	Pin 7

0xC800	OFF	OFF

0xCC00	ON	OFF

0xD800	OFF	ON

0xDC00	ON	ON

IRQ

Jumper Block J1

Pin 1	Pin 2	Pin 3	Pin 4

9	ON	OFF	OFF	OFF

10	OFF	ON	OFF	OFF

11	OFF	OFF	ON	OFF

12	OFF	OFF	OFF	ON

IRQ Channel

Jumper Block J2

Pin 1	Pin 2

9	OFF	OFF

10	ON	OFF

11	OFF	ON

12	ON	ON

Host Adapter BIOS

Jumper Block J1

Pin 8

Enabled	ON

Disabled	OFF

Port Address

Jumper Block J1

Pin 5

0x140	ON

0x340	OFF

SCSI Parity Check

Jumper Block J2

Pin 4

Enabled	OFF

Disabled	ON

SCSI Disconnection

Jumper Block J2

Pin 3

Enabled	ON

Disabled	OFF


Adaptec 1540A

This is the Adaptec 1540A SCSI adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base Memory Address, and other jumper/switch configurations:

SCSI Synchronous Negotiation

Jumper Block J1

Pin 1

Host Initiated	ON

Target Initiated	OFF

SCSI Parity

Jumper Block J1

Pin 3

Parity Checking Enabled	OFF

Parity Checking Disabled	ON

SCSI Address

Jumper Block J1

Pin 4	Pin 5	Pin 6

0	ON	ON	ON

1	OFF	ON	ON

2	ON	OFF	ON

3	OFF	OFF	ON

4	ON	ON	OFF

5	OFF	ON	OFF

6	ON	OFF	OFF

7	OFF	OFF	OFF

DMA Channel (using Jumper Blocks J1, J14, and J15)

DMA Channel

Jumper Block J1

Pin 7	Pin 8

0	ON	ON

5	OFF	ON

6	ON	OFF

7	OFF	OFF

DMA Channel Request

Pin 1	Pin 2	Pin 3	Pin 4

0	ON	OFF	OFF	OFF

5	OFF	ON	OFF	OFF

6	OFF	OFF	ON	OFF

7	OFF	OFF	OFF	ON

DMA Channel Acknowledge

Pin 1	Pin 2	Pin 3	Pin 4

0	ON	OFF	OFF	OFF

5	OFF	ON	OFF	OFF

6	OFF	OFF	ON	OFF

7	OFF	OFF	OFF	ON

AT Interrupt Channel (Using Jumper Blocks J1 and J16)

Interrupt Reported during Return Configuration Command

Jumper Block J1

Pin 9	Pin 10	Pin 11

9	OFF	OFF	OFF

10	ON	OFF	OFF

11	OFF	ON	OFF

12	ON	ON	OFF

14	OFF	OFF	ON

15	ON	OFF	ON

IRQ

Jumper Block J16

Pin 1	Pin 2	Pin 3	Pin 4	Pin 5	Pin 6

9	ON	OFF	OFF	OFF	OFF	OFF

10	OFF	ON	OFF	OFF	OFF	OFF

11	OFF	OFF	ON	OFF	OFF	OFF

12	OFF	OFF	OFF	ON	OFF	OFF

14	OFF	OFF	OFF	OFF	ON	OFF

15	OFF	OFF	OFF	OFF	OFF	ON

DMA Transfer Speed

Jumper Block J1

Pin 12	Pin 13

5.0 MB/s	OFF	OFF

5.7 MB/s	ON	OFF

6.7 MB/s	OFF	ON

8.0 MB/s	ON	ON

BIOS Wait State

Jumper Block J7

Pin 1	Pin 2	Pin 3	Pin 4

Disabled	ON	OFF	OFF	OFF

100 ns	OFF	ON	OFF	OFF

200 ns	OFF	OFF	ON	OFF

300 ns	OFF	OFF	OFF	ON

Port Address

Jumper Block J6

Pin 1	Pin 2	Pin 3

0x130	ON	OFF	ON

0x134	ON	OFF	OFF

0x230	OFF	ON	ON

0x234	OFF	ON	OFF

0x330	OFF	OFF	ON

0x334	OFF	OFF	OFF

BIOS Address

Jumper Block J10

Pin 1	Pin 2

0xC8000	ON	ON

0xD8000	OFF	ON

0xCC000	ON	OFF

0xDC000	OFF	OFF

BIOS Enable/Disable

Jumper Block J11

Enabled	ON

Disabled	OFF

Diskette Controller Secondary Address

Jumper Block J12

0x370	ON

0x3F0	OFF


Adaptec 1505

IRQ

Jumper Block J1

Pin 1	Pin 2	Pin 3	Pin 4

9	ON	OFF	OFF	OFF

10	OFF	ON	OFF	OFF

11	OFF	OFF	ON	OFF

12	OFF	OFF	OFF	ONF

PIO Port Address

Jumper Block J1

Pin 5

0x140	ON

0x340	OFF


Adaptech 1510 Card
Adaptec 1510

This is the Adaptec 1510 SCSI adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base Memory Address, and other jumper/switch configurations:

J9

IRQ	J10	J11	J12	J19

10	ON	OFF	OFF	OFF

11	OFF	ON	OFF	OFF

12	OFF	OFF	ON	OFF

9	OFF	OFF	OFF	ON

PORT ADDRESS	"SWITCH "AL"

340H	OFF

140H	ON


Adaptec 1540

This is the Adaptec 1540 SCSI adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base Memory Address, and other jumper/switch configurations:

SCSI ID

Jumper Block J1

Pin4	Pin5	Pin6

0	ON	ON	ON

1	OFF	ON	ON

2	ON	OFF	ON

3	OFF	OFF	ON

4	ON	ON	OFF

5	OFF	ON	OFF

6	ON	OFF	OFF

7	OFF	OFF	OFF

SCSI PARITY

Parity Checking Enabled	Pin 3 of J1 is OFF

Parity Checking Disabled	Pin 3 of J1 is ON

SCSI Terminators = RN6 & RN7

SCSI Synchronous Negotiation

Jumper Block J1

Pin 1

Host Initiated	ON

Target Initiated	OFF

DMA Channel Selection

Jumper Block J1

Pin 7	Pin 8

0	ON	ON

5	OFF	ON

6	ON	OFF

7	OFF	OFF

DMA Acknowledge

Jumper Block J7

Pin 1	Pin 2	Pin 3	Pin 4

0	ON	OFF	OFF	OFF

5	OFF	ON	OFF	OFF

6	OFF	OFF	ON	OFF

7	OFF	OFF	OFF	ON

DMA Request

Jumper Block J6

Pin 1	Pin 2	Pin 3	Pin 4

0	ON	OFF	OFF	OFF

5	OFF	ON	OFF	OFF

6	OFF	OFF	ON	OFF

7	OFF	OFF	OFF	ON

Interrupt Request

Jumper Block J1

Pin 9	Pin 10	Pin 11

9	OFF	OFF	OFF

10	ON	OFF	OFF

11	OFF	ON	OFF

12	ON	ON	OFF

14	OFF	OFF	ON

15	ON	OFF	ON

BIOS Address

Jumper Block J10

Pin 1	Pin 2	Pin 3

0xC8000	ON	OFF	ON

0xD8000	OFF	OFF	ON

0xCC000	ON	OFF	OFF

0xDC000	OFF	OFF	OFF


Adaptec 1520A/1522A

This is the Adaptec 1520A SCSI adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base Memory Address, and other jumper/switch configurations:

JUMPER BLOCK J5

Pin 1 Reserved

Pin 2 Reroute Int 19 when booting

Don't Reroute	OFF

Reroute	ON

Pins 3 & 4  Bootup Messages Displayed

Display Adaptec header and error messages	OFF	OFF

"Display Adaptec header, boot

progress and error messages"	OFF	ON

"Display SCSI information, jumper

configuration, boot progress, and

error messages"	ON	OFF

Display error messages	ON	ON

Pin 5	Synchronous Negotiation Enable/Disable

Pin 6	Disconnection by Target SCSI Device Enable/Disable

Pin 7	Not Used

Pin 8	Not Used

JUMPER BLOCK J6

SCSI ID

Pin 1	Pin 2	Pin 3

0	OFF	OFF	OFF

1	ON	OFF	OFF

2	OFF	ON	OFF

3	ON	ON	OFF

4	OFF	OFF	ON

5	ON	OFF	ON

6	OFF	ON	ON

7	ON	ON	ON

IRQ	J4	J5

9	OFF	OFF

10	ON	OFF

11	OFF	ON

12	ON	ON

Pins 6 & 7   Reserved

Pin 8	Parity Checking Enable/Disable

JUMPER BLOCK J7 (Adaptec 1522 Only)

Pin 1	Floppy Controller on Host Adapter Enable/Disable

JUMPER BLOCK J8

Jumper Block J8 is reserved for Adaptec use

JUMPER BLOCK J9

IRQ

(Must match settings on Jumper Block J6)

Pin 1	Pin 2	Pin 3	Pin 4

12	ON	OFF	OFF	OFF

11	OFF	ON	OFF	OFF

10	OFF	OFF	ON	OFF

9	OFF	OFF	OFF	ON

I/O PORT ADDRESS

Pin 5

0x340	OFF

0x140	ON

BIOS ADDRESS

Pin 6	Pin 7

C8000	OFF	OFF

CC000	OFF	ON

D8000	ON	OFF

C0000	ON	ON

Pin 8	Host Adapter Bios Enable/Disable


Adaptech 1520/1522 Card
Adaptec 1520/1522

This is the Adaptec 1520 SCSI adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base Memory Address, and other jumper/switch configurations:

JUMPER BLOCK J5

DATA TRANSFER MODE	J1

PIO	OFF

2nd Parity DMA	ON

BOOT PREFERENCE	J2

Don't boot from SCSI Drive	OFF

Boot From SCSI Drive	ON

BOOT UP MESSAGES	J3	J4

Display Adaptec header and error messages	OFF	OFF

"Display Adaptec header, boot

progress and error messages"	OFF	ON

"Display SCSI information, jumper

configuration, boot progress, and

error messages"	ON	OFF

Display error messages	ON	ON

J5	Synchronous Negotiation Enable/Disable

J6	Disconnection by Target SCSI Device Enable/Disable

J7	Not Used

J8	Not Used

JUMPER BLOCK J6

SCSI

ID	J1	J2	J3

0	OFF	OFF	OFF

1	ON	OFF	OFF

2	OFF	ON	OFF

3	ON	ON	OFF

4	OFF	OFF	ON

5	ON	OFF	ON

6	OFF	ON	ON

7	ON	ON	ON

IRQ	J4	J5

9	OFF	OFF

10	ON	OFF

11	OFF	ON

12	ON	ON

J6/J7	Both are left off to place card at DMA Channel 0 (The only channel supported by Adaptec)

J8	Parity Checking Enable/Disable

JUMPER BLOCK J7 (Adaptec 1522 Only)

J1	Floppy Controller on Host Adapter Enable/Disable

FLOPPY

IRQ CHANNEL	J6	J7

6	ON	OFF

10	OFF	ON

J8	Support for Floppy Drives with Dual Speed Spindle Enable/Disable

JUMPER BLOCK J8

Jumpers 4 & 8 should be on.  This selects DMA Channel 0.  All Other Jumpers are Reserved

JUMPER BLOCK J9

IRQ

(Must match settings on Jumper Block J6)

J1	J2	J3	J4

12	ON	OFF	OFF	OFF

11	OFF	ON	OFF	OFF

10	OFF	OFF	ON	OFF

9	OFF	OFF	OFF	ON

PORT

ADDRESS RANGE	J5

340-35E	OFF

140-15E	ON

BIOS

ADDRESS LOCATION	J6	J7

C8000	OFF	OFF

CC000	OFF	ON

D8000	ON	OFF

C0000	ON	ON

J8	Host Adapter Bios Enable/Disable


Adaptech 1540B/1542B Card
Adaptec 1540B/1542B

This is the Adaptec 1540B/1542B SCSI adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base Memory Address, and other jumper/switch configurations:

J5  - GENERAL CONTROLS

PIN 1	SYNCHRONOUS TRANSFER NEGOTIATION ENABLE/DISABLE

PIN 2	DIAGNOSTICS (USED ONLY AT ADAPTEC)

PIN 3	SCSI PARITY ENABLE/DISABLE

SCSI

I.D.	PIN 4	PIN 5	PIN 6

0	ON	ON	ON

1	OFF	ON	ON

2	ON	OFF	ON

3	OFF	OFF	ON

4	ON	ON	OFF

5	OFF	ON	OFF

6	ON	OFF	OFF

7	OFF	OFF	OFF

DMA

CHANNEL	PIN 7	PIN 8

0	ON	ON

5	OFF	ON

6	ON	OFF

7	OFF	OFF

IRQ 	PIN 9	PIN 10	PIN 11

9	OFF	OFF	OFF

10	ON	OFF	OFF

11	OFF	ON	OFF

12	ON	ON	OFF

14	OFF	OFF	ON

15	ON	OFF	ON

DMA

SPEED	PIN 12	PIN 13

5	OFF	OFF

5.7	ON	OFF

6.7	OFF	ON

8	ON	ON

J6 - BIOS/AUTO SENSE CONTROL

PIN 1	BIOS ENABLE

PIN 2	NOT USED

PIN 3	NOT USED

PIN 4	NOT USED

PIN 5	AUTO SENSE DISABLE

J7 - ADDRESS SELECTION

PIN 1	FLOPPY SECONDARY ADDRESS SELECT (1542B ONLY)

I/O

ADDRESS	PIN 2	PIN 3	PIN 4

130h	ON	OFF	ON

134h	OFF	OFF	ON

230h	ON	ON	OFF

234h	OFF	ON	OFF

330h	ON	OFF	OFF

334h	OFF	OFF	OFF

BIOS WAIT

STATE SELECT	PIN 5	PIN 6

0	OFF	OFF

100	ON	OFF

200	OFF	ON

300	ON	ON

BIOS

BASE ADDRESS	PIN 7	PIN 8

DC000	OFF	OFF

CC000	ON	OFF

D8000	OFF	ON

C8000	ON	ON

J8 - FLOPPY DISK SELECTION (AHA-1542B ONLY)

Note - On 1542BS100 series, if the floppy enable is removed, remove all jumpers from J8.

PIN 1	FLOPPY ENABLE

PIN 2	DMA REQUEST 2

PIN 3	DMA REQUEST 3

PIN 4	DMA ACK 2

PIN 5	DMA ACK 3

PIN 6	INT REQUEST 6

PIN 7	INT REQUEST 10

PIN 8	DUAL SPEED ENABLE

J9 - DMA/INTERRUPT SELECTION

PIN 1	DMA REQUEST 0

PIN 2	DMA REQUEST 5

PIN 3	DMA REQUEST 6

PIN 4	DMA REQUEST 7

PIN 5	DMA ACK  0

PIN 6	DMA ACK 5

PIN 7	DMA ACK 6

PIN 8	DMA ACK 7

PIN 9	INT REQUEST 9

PIN 10	INT REQUEST 10

PIN 11	INT REQUEST 11

PIN 12	INT REQUEST 12

PIN 13	INT REQUEST 14

PIN 14	INT REQUEST 15


Adaptech 1540C/1542C Card
Adaptec 1540C/1542C

This is the Adaptec 1540C/1542C SCSI adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base Memory Address, and other jumper/switch configurations:

TERMINATION	SW1

Termination Installed	ON

Software Controlled	OFF

IO PORT	SW2	SW3	SW4

330-333H	OFF	OFF	OFF

334-337H	ON	OFF	OFF

230-233H	OFF	ON	OFF

234-237H	ON	ON	OFF

130-133H	OFF	OFF	ON

134-137H	ON	OFF	ON

Reserved	OFF	ON	ON

Reserved	ON	ON	ON

FLOPPY SUPPORT	SW5

Disable Floppy	ON

Enable Floppy	OFF

BIOS ADDRESS	SW6	SW7	SW8

DC000H	OFF	OFF	OFF

D8000H	ON	OFF	OFF

D4000H	OFF	ON	OFF

D0000H	ON	ON	OFF

CC000H	OFF	OFF	ON

C8000H	ON	OFF	ON

Reserved	OFF	ON	ON

Bios Disable	ON	ON	ON

The remaining settings for this SCSI interface card can be configured using the software supplied by the manufacturer.  Please consult the documentation that came with your SCSI interface card or contact the manufacturer of the SCSI interface card for further information.


Adaptech 1640 Card
Adaptec 1640

This SCSI interface card can be configured using the software supplied by the manufacturer. Please consult the documentation that came with your SCSI interface card or contact the manufacturer of the SCSI interface card for further information.


Adaptech 1740/1744 Card
Adaptec 1740/1744

This SCSI interface card can be configured using the software supplied by the manufacturer. Please consult the documentation that came with your SCSI interface card or contact the manufacturer of the SCSI interface card for further information.

Note1: - Terminators are RN2, RN3, and RN4.  Remove if the the adapter is not the first or last device on the SCSI bus.

Note2: - The 1744 is a differential controller.  While the firmware & BIOS are the same as that of the 1740/1742, the electrical interface is different. It should NEVER be connected to any single ended SCSI devices as you may damage either the host adapter or your SCSI devices.


Adaptech 1740A/1744A Card
Adaptec 1740A/1744A

This SCSI interface card can be configured using the software supplied by the manufacturer.  Please consult the documentation that came with your SCSI interface card or contact the manufacturer of the SCSI interface card for further information.

Note1: The only manually configurable jumpers are documented on the illustration above.  Terminators are RN5, RN6, and RN7.  Remove if the the adapter is not the first or last device on the SCSI bus.

Note2: - The 1744 is a differential controller.  While the firmware & BIOS are the same as that of the 1740/1742, the electrical interface is different.  It should NEVER be connected to any single ended SCSI devices as you may damage either the host adapter or your SCSI devices.


BusLogic Cards
BusLogic

Windows 95 Adapter help currently includes the following BusLogic SCSI interface cards:

BT-445S

BT-542B

BT-542D

BT-542S

BT-545S

BT-640A

BT-646S/646D

BT-742A

BT-747S/747D


BusLogic BT-445S Card
BusLogic BT-445S

This is the BusLogic 445S SCSI adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base Memory Address, and other jumper/switch configurations:

Switch Bay 1

SCSI

ID	S1	S2	S3

0	OFF	OFF	OFF

1	ON	OFF	OFF

2	OFF	ON	OFF

3	ON	ON	OFF

4	OFF	OFF	ON

5	ON	OFF	ON

6	OFF	ON	ON

7	ON	ON	ON

SCSI Parity	S4

Disable	OFF

Enable	ON

More than

1Gb Support	S5

Disable	OFF

Enable	ON

Synchronous

Negotiation	S6

Disable	OFF

Enable	ON

SCSI

Transfer Speed	S7

10 Mb/Sec	OFF

5 MB/Sec	ON

VL-Bus

Clock Speed	S8	S9	S10

20 MHZ	ON	ON	OFF

25 MHZ	OFF	ON	OFF

33, 40 MHZ	ON	ON	ON

50 MHZ	ON	OFF	ON

DX2/50 MHZ	OFF	ON	OFF

DX2/66 MHZ	ON	ON	ON

Switch Bay 2

I/O Address	S1	S2	S3

Reserved	OFF	OFF	OFF

134h-137h	ON	OFF	OFF

234h-237h	OFF	ON	OFF

334h-337h	ON	ON	OFF

Reserved	OFF	OFF	ON

130h-133h	ON	OFF	ON

230h-233h	OFF	ON	ON

330h-333h	ON	ON	ON

Bios

Address	S4	S5

0C8000h	OFF	OFF

Disable	ON	OFF

0D8000h	OFF	ON

0DC000h	ON	ON

Host Interrupt

Channel	S6	S7	S8

Reserved	OFF	OFF	OFF

Reserved	ON	OFF	OFF

15	OFF	ON	OFF

14	ON	ON	OFF

12	OFF	OFF	ON

9	ON	OFF	ON

10	OFF	ON	ON

11	ON	ON	ON

S9	Reserved

S10	Reserved

JUMPERS

Host Interrupt

Channel	W3	W4	W5	W6	W7	W8

15	ON	OFF	OFF	OFF	OFF	OFF

14	OFF	ON	OFF	OFF	OFF	OFF

12	OFF	OFF	ON	OFF	OFF	OFF

11	OFF	OFF	OFF	ON	OFF	OFF

10	OFF	OFF	OFF	OFF	ON	OFF

9	OFF	OFF	OFF	OFF	OFF	ON

Floppy

Controller	W15	W16

Enable	ON	ON

Disable	OFF	OFF

Floppy

Address	W14

3FX	OFF

37X	ON


BusLogic BT-542B Card
BusLogic BT-542B

This is the BusLogic 542B SCSI adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base Memory Address, and other jumper/switch configurations:

SWITCH BAY 1

SCSI	SW1	SW2	SW3

ID

0	OFF	OFF 	OFF

1	ON	OFF 	OFF

2	OFF	ON	OFF

3	ON	ON	OFF

4	OFF	OFF 	ON

5	ON	OFF 	ON

6	OFF	ON	ON

7	ON	ON	ON

SW4

SCSI PARITY ENABLE/DISABLE

SW5

DISK > 1GB and not SCO UNIX ENABLE/DISABLE

SW6

SCSI SYNCHRONIZATION NEGOTIATION ENABLE/DISABLE

DMA

CHANNEL	SW7	SW8

DISABLE	OFF	OFF

5	ON	ON

6	OFF	ON

7	ON	OFF

SWITCH BAY 2

I/O

ADDRESS	SW1	SW2	SW3

Reserved	OFF	OFF	OFF

134H-137H	ON	OFF	OFF

234H-237H	OFF	ON	OFF

334H-337H	ON	ON	OFF

Reserved	OFF	OFF	ON

130H-133H	ON	OFF	ON

230H-233H	OFF	ON	ON

330H-333H	ON	ON	ON

BIOS BASE

ADDRESS	SW4	SW5

0C8000H	OFF	OFF

Disable	ON	OFF

0D8000H	OFF	ON

0DC000H	ON	ON

AT IRQ	SW6	SW7	SW8

Reserved	OFF	OFF	OFF

Reserved	ON	OFF	OFF

15	OFF	ON	OFF

14	ON	ON	OFF

12	OFF	OFF	ON

9	ON	OFF	ON

10	OFF	ON	ON

11	ON	ON	ON

JUMPER SETTINGS

HOST IRQ	W3	W4	W5	W6	W7	W8

9	OFF	OFF	OFF	OFF	OFF	ON

10	OFF	OFF	OFF	OFF	ON	OFF

11	OFF	OFF	OFF	ON	OFF	OFF

12	OFF	OFF	ON	OFF	OFF	OFF

14	OFF	ON	OFF	OFF	OFF	OFF

15	ON	OFF	OFF	OFF	OFF	OFF

HOST BUS

TRANSFER RATE	W11	W13

5.0 MB/SEC.	OFF	OFF

5.7 MB/SEC.	OFF	ON

6.7 MB/SEC.	ON	OFF

8.0 MB/SEC.	ON	ON

W17

HOST I/O CNANNEL READY ENABLE/DISABLE

FLOPPY I/O

ADDRESS	W14

PRIMARY (3FX)	OFF

SECONDARY (37X)	ON

FLOPPY

CONTROLLER	W15	W16

DISABLE	OFF	OFF

ENABLE	ON	ON


BusLogic BT-542D Card
BusLogic BT-542D

This is the BusLogic 542D SCSI adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base Memory Address, and other jumper/switch configurations:

SWITCH BAY 1

SCSI

ID	SW1	SW2	SW3

0	OFF	OFF 	OFF

1	ON	OFF 	OFF

2	OFF	ON	OFF

3	ON	ON	OFF

4	OFF	OFF 	ON

5	ON	OFF 	ON

6	OFF	ON	ON

7	ON	ON	ON

SW4

SCSI PARITY ENABLE/DISABLE

SW5

DISK > 1GB and not SCO UNIX ENABLE/DISABLE

SW6

SCSI SYNCHRONIZATION NEGOTIATION ENABLE/DISABLE

DMA

CHANNEL	SW7	SW8

Disable	OFF	OFF

5	ON	ON

6	OFF	ON

7	ON	OFF

SWITCH BAY 2

I/O

ADDRESS	SW1	SW2	SW3

Reserved	OFF	OFF	OFF

134H-137H	ON	OFF	OFF

234H-237H	OFF	ON	OFF

334H-337H	ON	ON	OFF

Reserved	OFF	OFF	ON

130H-133H	ON	OFF	ON

230H-233H	OFF	ON	ON

330H-333H	ON	ON	ON

AT

IRQ	SW6	SW7	SW8

Reserved	OFF	OFF	OFF

Reserved	ON	OFF	OFF

15	OFF	ON	OFF

14	ON	ON	OFF

12	OFF	OFF	ON

9	ON	OFF	ON

10	OFF	ON	ON

11	ON	ON	ON

SWITCH BAY 3

BIOS

ADDRESS	SW3	SW4	SW5

Disable	OFF	OFF	OFF

Reserved	ON	OFF	OFF

0C8000H	OFF	ON	OFF

0CC000H	ON	ON	OFF

0D0000H	OFF	OFF	ON

0D4000H	ON	OFF	ON

0D8000H	OFF	ON	ON

0DC000H	ON	ON	ON

MAXIMUM SYNCHRONOUS

DATA RATE	SW6

10.0 MB/SEC.	OFF

5 MB/SEC.	ON

SW7

Reserved

SW8

Reserved

HOST BUS

TRANSFER RATE	SW1	SW2

8.0 MB/SEC.	OFF	OFF

6.7 MB/SEC.	ON	OFF

5.7 MB/SEC.	OFF	ON

5.0 MB/SEC.	ON	ON

JUMPER SETTINGS

HOST

IRQ	W3	W4	W5	W6	W7	W8

9	OFF	OFF	OFF	OFF	OFF	ON

10	OFF	OFF	OFF	OFF	ON	OFF

11	OFF	OFF	OFF	ON	OFF	OFF

12	OFF	OFF	ON	OFF	OFF	OFF

14	OFF	ON	OFF	OFF	OFF	OFF

15	ON	OFF	OFF	OFF	OFF	OFF

W17

HOST I/O CNANNEL READY ENABLE/DISABLE

FLOPPY I/O

ADDRESS	W14

PRIMARY (3FX)	OFF

SECONDARY (37X)	ON

FLOPPY

CONTROLLER	W15	W16

DISABLE	OFF	OFF

ENABLE	ON	ON


BusLogic BT-542S Card
BusLogic BT-542S

This is the BusLogic 542S SCSI adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base Memory Address, and other jumper/switch configurations:

SWITCH BAY 1

SCSI

ID	SW1	SW2	SW3

0	OFF	OFF 	OFF

1	ON	OFF 	OFF

2	OFF	ON	OFF

3	ON	ON	OFF

4	OFF	OFF 	ON

5	ON	OFF 	ON

6	OFF	ON	ON

7	ON	ON	ON

SW4

SCSI PARITY ENABLE/DISABLE

SW5

DISK > 1GB and not SCO UNIX ENABLE/DISABLE

SW6

SCSI SYNCHRONIZATION NEGOTIATION ENABLE/DISABLE

DMA

CHANNEL	SW7	SW8

Disable	OFF	OFF

5	ON	ON

6	OFF	ON

7	ON	OFF

SWITCH BAY 2

I/O

ADDRESS	SW1	SW2	SW3

Reserved	OFF	OFF	OFF

134H-137H	ON	OFF	OFF

234H-237H	OFF	ON	OFF

334H-337H	ON	ON	OFF

Reserved	OFF	OFF	ON

130H-133H	ON	OFF	ON

230H-233H	OFF	ON	ON

330H-333H	ON	ON	ON

AT

IRQ	SW6	SW7	SW8

Reserved	OFF	OFF	OFF

Reserved	ON	OFF	OFF

15	OFF	ON	OFF

14	ON	ON	OFF

12	OFF	OFF	ON

9	ON	OFF	ON

10	OFF	ON	ON

11	ON	ON	ON

SWITCH BAY 3

BIOS

ADDRESS	SW3	SW4	SW5

Disable	OFF	OFF	OFF

Reserved	ON	OFF	OFF

0C8000H	OFF	ON	OFF

0CC000H	ON	ON	OFF

0D0000H	OFF	OFF	ON

0D4000H	ON	OFF	ON

0D8000H	OFF	ON	ON

0DC000H	ON	ON	ON

SW6

Reserved

SW7

Reserved

SW8

Reserved

HOST BUS

TRANSFER RATE	SW1	SW2

8.0 MB/SEC.	OFF	OFF

6.7 MB/SEC.	ON	OFF

5.7 MB/SEC.	OFF	ON

5.0 MB/SEC.	ON	ON

JUMPER SETTINGS

HOST

IRQ	W3	W4	W5	W6	W7	W8

9	OFF	OFF	OFF	OFF	OFF	ON

10	OFF	OFF	OFF	OFF	ON	OFF

11	OFF	OFF	OFF	ON	OFF	OFF

12	OFF	OFF	ON	OFF	OFF	OFF

14	OFF	ON	OFF	OFF	OFF	OFF

15	ON	OFF	OFF	OFF	OFF	OFF

W17

HOST I/O CNANNEL READY ENABLE/DISABLE

FLOPPY I/O

ADDRESS	W14

PRIMARY (3FX)	OFF

SECONDARY (37X)	ON

FLOPPY

CONTROLLER	W15	W16

DISABLE	OFF	OFF

ENABLE	ON	ON


BusLogic BT-545S Card
BusLogic BT-545S

This is the BusLogic 545S SCSI adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base Memory Address, and other jumper/switch configurations:

Switch Bay 1

SCSI

ID	S1	S2	S3

0	OFF	OFF	OFF

1	ON	OFF	OFF

2	OFF	ON	OFF

3	ON	ON	OFF

4	OFF	OFF	ON

5	ON	OFF	ON

6	OFF	ON	ON

7	ON	ON	ON

SCSI

Parity	S4

Disable	OFF

Enable	ON

More than

1Gb Support	S5

Disable	OFF

Enable	ON

Synchronous

Negotiation	S6

Disable	OFF

Enable	ON

DMA

Channel	S7	S8

Disable	OFF	OFF

7	ON	OFF

6	OFF	ON

5	ON	ON

Switch Bay 2

I/O

Port Address	S1	S2	S3

Reserved	OFF	OFF	OFF

134h-137h	ON	OFF	OFF

234h-237h	OFF	ON	OFF

334h-337h	ON	ON	OFF

Reserved	OFF	OFF	ON

130h-133h	ON	OFF	ON

230h-233h	OFF	ON	ON

330h-333h	ON	ON	ON

Bios

Address	S4	S5

0C8000h	OFF	OFF

Disable	ON	OFF

0D8000h	OFF	ON

0DC000h	ON	ON

Host

Interrupt Channel	S6	S7	S8

Reserved	OFF	OFF	OFF

Reserved	ON	OFF	OFF

15	OFF	ON	OFF

14	ON	ON	OFF

12	OFF	OFF	ON

9	ON	OFF	ON

10	OFF	ON	ON

11	ON	ON	ON

Jumpers

Host

Interrupt Channel	W3	W4	W5	W6	W7	W8

15	ON	OFF	OFF	OFF	OFF	OFF

14	OFF	ON	OFF	OFF	OFF	OFF

12	OFF	OFF	ON	OFF	OFF	OFF

11	OFF	OFF	OFF	ON	OFF	OFF

10	OFF	OFF	OFF	OFF	ON	OFF

9	OFF	OFF	OFF	OFF	OFF	ON

Bus

Transfer Rate	W11	W13

5.0 MB/Sec	OFF	OFF

5.7 MB/Sec	OFF	ON

6.7 MB/Sec	ON	OFF

8.0 MB/Sec	ON	ON

Floppy

Controller	W15	W16

Enable	ON	ON

Disable	OFF	OFF

Floppy

Address	W14

3FX	OFF

37X	ON

I/O

Channel Read	W17

Enable	A-B

Disable	B-C

W18	Reserved

Max

Synchronous Rate	W19

5 MB/Sec	ON

10 MB/Sec	OFF


BusLogic BT-640A Card
BusLogic BT-640A

This SCSI interface card can be configured using the software supplied by the manufacturer.  Please consult the documentation that came with your SCSI interface card or contact the manufacturer of the SCSI interface card for further information.

BIOS Address

Default - DC00h

I/O Port Address

Default - 330h

Arbitration Level

Default - Level 5

Arbitration Firmware

Default - ON

IRQ

Default - 15

SCSI ID

Default - 7

Adapter Sync

Default - ON

Adapter SCSI parity checking

Default - ON


BusLogic BT-646S/646D Card
BusLogic BT-646S/646D

Note - The BT-746S supports the single-ended SCSI interface with active termination.  The BT-746D supports the differential SCSI interface.

This SCSI interface card can be configured using the software supplied by the manufacturer.  Please consult the documentation that came with your SCSI interface card or contact the manufacturer of the SCSI interface card for further information.

BIOS Address

Default - DC00h

I/O Port Address

Default - 330h

Arbitration Level

Default - Level 5

Arbitration Fairness

Default - ON

IRQ

Default - 15

SCSI ID

Default - 7

Adapter Sync

Default - ON

Adapter SCSI parity checking

Default - ON


BusLogic BT-742A Card
BusLogic BT-742A

W8

Floppy enable/disable

The remaining settings for this SCSI interface card can be configured using the software supplied by the manufacturer.  Please consult the documentation that came with your SCSI interface card or contact the manufacturer of the SCSI interface card for further information.

Note:  Terminators are RN2, RN3, and RN4.  Remove if the the adapter is not the first or last device on the SCSI bus.

BIOS Address

Default - DC00h 16K

I/O Port Address

Default - 330h

IRQ

Default - 11

SCSI ID

Default - 7

Adapter Sync

Default - OFF

Adapter SCSI parity checking

Default - ON

DMA Channel

Default - 5


BusLogic BT-747S/747D Card
BusLogic BT-747S/747D

W8

Floppy enable/disable

BIOS Address

Default - DC00h 16K

I/O Port Address

Default - 330h

IRQ

Default - 11

SCSI ID

Default - 7

Adapter Sync

Default - OFF

Adapter SCSI parity checking

Default - ON

DMA Channel

Default - 5

Note - The BT-747S supports the single-ended SCSI interface with active termination.  The BT-747D supports the differential SCSI interface.

The remaining settings for this SCSI interface card can be configured using the software supplied by the manufacturer.  Please consult the documentation that came with your SCSI interface card or contact the manufacturer of the SCSI interface card for further information.


DPT Cards
DPT

Windows 95 Adapter help currently includes the following DPT SCSI cards:

PM2011

PM2012


DPT PM2012 Card
DPT PM2012

This is the DPT PM2012 SCSI adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base Memory Address, and other jumper/switch configurations:

SWITCH BAY 1

SW1

Busy

SW2

Computer bus transfer to controller

SW3

Computer bus transfer from controller

SW4

Cache hit

SW5

Disk read-ahead active

SW6

Disk read

SW7

Disk write

SW8

Controller reset

SW9

Controller interrupt pending to computer

SW10

DAQ asserted to computer

JUMPERS

W7

DPT ROM ENABLE/DISABLE

DPT ROM

ADDRESS	W19

C8000	OFF

D8000	ON

The remaining settings for this SCSI interface card can be configured using the software supplied by the manufacturer.  Please consult the documentation that came with your SCSI interface card or contact the manufacturer of the SCSI interface card for further information.


DPT PM2011 Card
DPT PM2011

This is the DPT PM2011 SCSI adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base Memory Address, and other jumper/switch configurations:

Jumpers

Floppy Drive	Y20

Enable	OFF

Disable	ON

Floppy

Address	Y34

3F0h	OFF

370h	ON

Optional

ROM Address	Y36	Y37

C8000h	ON	ON

D8000h	ON	OFF

DC000h	OFF	ON

Disabled	OFF	OFF

SCSI

ID	Y25	Y18	Y26

7	ON	ON	ON

6	OFF	ON	ON

5	ON	OFF	ON

4	OFF	OFF	ON

3	ON	ON	OFF

2	OFF	ON	OFF

1	ON	OFF	OFF

0	OFF	OFF	OFF

MEMCS16

(ISA Memory)	Y21	Y28	Memory

Ignore MEMCS16	OFF	ON	16-bit

Decode MEMCS16	ON	OFF	8 or 16-bit

Address Lines Used	Y19

SA17-19 & LA17-19 driven	ON

Only LA17-19 driven	OFF

DMA Speed	Y27

4 MB/Sec	ON

5 MB/Sec	OFF

Bus Mastering	Y24

Enabled	OFF

Disabled	ON

EPROM Size

(Jumper Y23)	Post 1	Post 2	Post 3

256K	OFF	ON	ON

512K	ON	ON	OFF


DTC Cards
DTC

Windows 95 Adapter help currently includes the following DTC SCSI cards:

DTC 3192

DTC 3292


DTC 3192 Card
DTC 3192

This SCSI interface card can be configured using the software supplied by the manufacturer.  Please consult the documentation that came with your SCSI interface card or contact the manufacturer of the SCSI interface card for further information.

BIOS Address

Default - D800h

I/O Port Address

Default - 330h

IRQ

Default - 11

SCSI ID

Default - 7

Adapter SCSI parity checking

Default - OFF

Floppy Disk Controller

Default - ON

SCSI Cold Boot Delay

Default - 10sec

Start SCSI Delay

Default - OFF

SCSI Auto Synchronous Negotiation

Default - OFF


DTC 3292 Card
DTC 3292

This SCSI interface card can be configured using the software supplied by the manufacturer.  Please consult the documentation that came with your SCSI interface card or contact the manufacturer of the SCSI interface card for further information.

BIOS Address

Default - D800h

I/O Port Address

Default - 330h

IRQ

Default - 11

SCSI ID

Default - 7

Adapter SCSI parity checking

Default - OFF

Floppy Disk Controller

Default - ON

SCSI Cold Boot Delay

Default - 10sec

Start SCSI Delay

Default - OFF

SCSI Auto Synchronous Negotiation

Default - OFF


Future Domain Cards
Future Domain

Windows 95 Adapter help currently includes the following Future Domain SCSI cards:

MCS-600

MCS-700

TMC-845

TMC-850-M

TMC-860M/885M

TMC-1650

TMC-1660

TMC-1670

TMC-1680

TMC-7000EX


Future Domain MCS-600 Card
Future Domain MCS-600

This is the Future Domain MCS-600 SCSI adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base Memory Address, and other jumper/switch configurations:

W4

Termination Power Enable/Disable

The remaining settings for this SCSI interface card can be configured using the software supplied by the manufacturer.  Please consult the documentation that came with your SCSI interface card or contact the manufacturer of the SCSI interface card for further information.

Interrupt Request Line (IRQ)

Default - IRQ5

Base I/O Address

Default - 140h

Base Memory Address

Default - CA00h


Future Domain MCS-700 Card
Future Domain MCS-700

This is the Future Domain MCS-700 SCSI adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base Memory Address, and other jumper/switch configurations:

W1

Termination Power Enable/Disable

The remaining settings for this SCSI interface card can be configured using the software supplied by the manufacturer.  Please consult the documentation that came with your SCSI interface card or contact the manufacturer of the SCSI interface card for further information.

Interrupt Request Line (IRQ)

Default - IRQ5

Base I/O Address

Default - 140h

Base Memory Address

Default - CA00h


Future Domain TMC-845 Card
Future Domain TMC-845

This is the Future Domain TMC-845 SCSI adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base Memory Address, and other jumper/switch configurations:

ADDRESS	W1	W2

CA00H	OFF	OFF

C800H	OFF	ON

CE00H	ON	OFF

DE00H	ON	ON

IRQ	W3	CENTER	W4

POST

3	ON	ON	OFF

5	OFF	ON	ON

The remaining settings for this SCSI interface card can be configured using the software supplied by the manufacturer.  Please consult the documentation that came with your SCSI interface card or contact the manufacturer of the SCSI interface card for further information.


Future Domain TMC-850-M Card
Future Domain TMC-850-M

This is the Future Domain TMC-850-M SCSI adapter shown above.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base Memory Address, and other jumper/switch configurations:

BIOS BASE

ADDRESS	W1	W2	W3

CA00H	OFF	OFF	"1-2, 3-4"

C800H	OFF	ON	"1-2, 3-4"

CE00H	ON	OFF	"1-2, 3-4"

DE00H	ON	ON	"1-2, 3-4"

E800H	OFF	OFF	"1-3, 2-4"

EC00H	ON	OFF	"1-3, 2-4"

W4

Termination Power Enable/Disable (Shorted/Open)

W5

Zero Wait State Enable/Disable (Shorted/Open)

IRQ	W6	CENTER	W7

POST

3	ON	ON	OFF

5	OFF	ON	ON


Future Domain TMC-860M/885M Card
Future Domain TMC-860M/885M

This is the Future Domain TMC-860M/885M SCSI adapter shown above.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base Memory Address, and other jumper/switch configurations:

BIOS BASE

ADDRESS	W1	W2	W3

CA00H	OFF	OFF	"1-2, 3-4"

C800H	OFF	ON	"1-2, 3-4"

CE00H	ON	OFF	"1-2, 3-4"

DE00H	ON	ON	"1-2, 3-4"

E800H	OFF	OFF	"1-3, 2-4"

EC00H	ON	OFF	"1-3, 2-4"

W4

Termination Power Enable/Disable (Shorted/Open)

W5

Zero Wait State Enable/Disable (Shorted/Open)

W6

(TMC-885M Only)	PIN 1-2	PIN 3-4	PIN 5-6

Floppy Circuit Enable	ON	ON	ON

Floppy Circuit Disable	OFF	OFF	OFF

W7

IRQ	P1-2	P3-4	P5-6	P7-8	P9-10	P11-12	P13-14	P15-16

3	ON	OFF	OFF	OFF	OFF	OFF	OFF	OFF

4	OFF	ON	OFF	OFF	OFF	OFF	OFF	OFF

5	OFF	OFF	ON	OFF	OFF	OFF	OFF	OFF

10	OFF	OFF	OFF	ON	OFF	OFF	OFF	OFF

11	OFF	OFF	OFF	OFF	ON	OFF	OFF	OFF

12	OFF	OFF	OFF	OFF	OFF	ON	OFF	OFF

14	OFF	OFF	OFF	OFF	OFF	OFF	ON	OFF

15	OFF	OFF	OFF	OFF	OFF	OFF	OFF	ON


Future Domain TMC-1650 Card
Future Domain TMC-1650

This is the Future Domain TMC-1650 SCSI adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base Memory Address, and other jumper/switch configurations:

W1

IRQ	J1	J2	J3

3	OFF	OFF	OFF

5	ON	OFF	OFF

10	OFF	ON	OFF

11	ON	ON	OFF

12	OFF	OFF	ON

14	ON	OFF	ON

15	OFF	ON	ON

Disabled	ON	ON	ON

I/O

ADDRESS	J4	J5

0140-014F	OFF	OFF

0150-015F	ON	OFF

0160-016F	OFF	ON

0170-017F	ON	ON

MEMORY

ADDRESS	J6	J7

C8000-C9FFF	OFF	OFF

CA000-CBFFF	ON	OFF

CE000-CFFFF	OFF	ON

DE000-DEFFF	ON	ON

W2

ROM	J1	J2

ENABLE	ON	ON

DISABLE	OFF	OFF

W4

Termination Power Enable/Disable


Future Domain TMC-1660 Card
Future Domain TMC-1660

This is the Future Domain TMC-1660 SCSI adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base Memory Address, and other jumper/switch configurations:

W1

IRQ	J1	J2	J3

3	OFF	OFF	OFF

5	ON	OFF	OFF

10	OFF	ON	OFF

11	ON	ON	OFF

12	OFF	OFF	ON

14	ON	OFF	ON

15	OFF	ON	ON

Disabled	ON	ON	ON

I/O

ADDRESS	J4	J5

0140-014F	OFF	OFF

0150-015F	ON	OFF

0160-016F	OFF	ON

0170-017F	ON	ON

MEMORY

ADDRESS	J6	J7

C8000-C9FFF	OFF	OFF

CA000-CBFFF	ON	OFF

CE000-CFFFF	OFF	ON

DE000-DFFFF	ON	ON

W3

FLOPPY	J1	J2	J3

ENABLE	ON	ON	ON

DISABLE	OFF	OFF	OFF

W4

Termination Power Enable/Disable


Future Domain TMC-1670 Card
Future Domain TMC-1670

This is the Future Domain TMC-1670 SCSI adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base Memory Address, and other jumper/switch configurations:

W1

IRQ	J1	J2	J3

3	OFF	OFF	OFF

5	ON	OFF	OFF

10	OFF	ON	OFF

11	ON	ON	OFF

12	OFF	OFF	ON

14	ON	OFF	ON

15	OFF	ON	ON

Disabled	ON	ON	ON

I/O

ADDRESS	J4	J5

0140-014F	OFF	OFF

0150-015F	ON	OFF

0160-016F	OFF	ON

0170-017F	ON	ON

MEMORY

ADDRESS	J6	J7

C8000-C9FFF	OFF	OFF

CA000-CBFFF	ON	OFF

CE000-CFFFF	OFF	ON

DE000-DFFFF	ON	ON

W2

ROM	J1	J2

ENABLE	ON	ON

DISABLE	OFF	OFF

W3

FLOPPY	J1	J2	J3

ENABLE	ON	ON	ON

DISABLE	OFF	OFF	OFF

W4

Termination Power Enable/Disable


Future Domain TMC-1680 Card
Future Domain TMC-1680

This is the Future Domain TMC-1680 SCSI adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base Memory Address, and other jumper/switch configurations:

W1

IRQ	J1	J2	J3

3	OFF	OFF	OFF

5	ON	OFF	OFF

10	OFF	ON	OFF

11	ON	ON	OFF

12	OFF	OFF	ON

14	ON	OFF	ON

15	OFF	ON	ON

Disabled	ON	ON	ON

I/O

ADDRESS	J4	J5

0140-014F	OFF	OFF

0150-015F	ON	OFF

0160-016F	OFF	ON

0170-017F	ON	ON

MEMORY

ADDRESS	J6	J7

C8000-C9FFF	OFF	OFF

CA000-CBFFF	ON	OFF

CE000-CFFFF	OFF	ON

DE000-DFFFF	ON	ON

W2

JUMPER 1

PRIMARY DISKETTE ENABLE/DISABLE

JUMPER 2

SECONDARY DISKETTE ENABLE/DISABLE

JUMPER 3

AT DISK CONTROLLER ENABLE/DISABLE

JUMPER 4

ROM ENABLE/DISABLE

JUMPER 5

ROM AND RAM ENABLE/DISABLE

W3

FLOPPY	J1	J2	J3

ENABLE	ON	ON	ON

DISABLE	OFF	OFF	OFF

W4

TERMINATION POWER ENABLE/DISABLE


Future Domain TMC-7000EX Card
Future Domain TMC-7000EX

This SCSI interface card can be configured using the software supplied by the manufacturer.  Please consult the documentation that came with your SCSI interface card or contact the manufacturer of the SCSI interface card for further information.

Interrupt Request Line (IRQ)

Default - IRQ14

Base Memory Address

Default - DC000h - DFFFFh


IBM Cards
IBM

Windows 95 Adapter help currently includes the following IBM SCSI cards:

IBM PS/2 Microchannel SCSI Host Adapter


IBM PS/2 SCSI Host Adapter

This SCSI interface card can be configured using the software supplied by the manufacturer.  Please consult the documentation that came with your SCSI interface card or contact the manufacturer of the SCSI interface card for further information.


NCR Cards
NCR

Windows 95 Adapter help currently includes the following NCR SCSI cards:

NCR 53C90

NCR 53C700

NCR 53C710


NCR 53C90 Card
NCR 53C90

This is the NCR 53C90 SCSI adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base Memory Address, and other jumper/switch configurations:

Need Doc's!!


NCR 53C700 Card
NCR 53C700

This is the NCR 53C700 SCSI adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base Memory Address, and other jumper/switch configurations:

Need Doc's!!


NCR 53C710 Card
NCR 53C710

This is the NCR 53C710 SCSI adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base Memory Address, and other jumper/switch configurations:

Need Doc's!!


UltraStor Cards
UltraStor

Windows 95 Adapter help currently includes the following UltraStor SCSI cards:

UltraStor 14F

UltraStor 24F

UltraStor 34F


UltraStor 14F Card
UltraStor 14F

This is the UltraStor 14F SCSI adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base Memory Address, and other jumper/switch configurations:

JP2

Floppy Control Enable/Disable

JP11 (JUMPER BLOCK 1)

DMA

CHANNEL	J1-2	J3-4

5	OFF	OFF

6	OFF	ON

7	ON	OFF

Reserved	ON	ON

IRQ	J5-6	J7-8

10	ON	ON

11	ON	OFF

14	OFF	ON

15	OFF	OFF

J9-J10

RESERVED

BIOS

SEGMENT	J11-12	J13-14	J15-16

Disable	OFF	OFF	OFF

C4000-C7FFF	OFF	OFF	ON

C8000-CBFFF	OFF	ON	OFF

CC000-CFFFF	OFF	ON	ON

D0000-D3FFF	ON	OFF	OFF

D4000-D7FFF	ON	OFF	ON

D8000-DBFFF	ON	ON	OFF

DC000-DFFFF	ON	ON	ON

JP12 (JUMPER BLOCK 2)

ISA TASK FILE

REGISTER ADDRESS	J1-2	J3-4

"1F0H-1F7H, 3F6-3F7"	OFF	OFF

"170H-177H, 376-377"	OFF	ON

Disable	ON	ON

NUMBER OF

HARD DRIVES	J5-6

2 (MAX) HD PER SYSTEM	OFF

7 (MAX) HD PER HOST ADAPTER	ON

HEAD MAPPING MODE	J7-8	J9-10

16 HEAD; 63 SECTOR MAPPING	OFF	OFF

64 HEAD; 32 SECTOR MAPPING	OFF	ON

64 HEAD; 63 SECTOR MAPPING	ON	OFF

64 HEAD; 32 SECTOR MAPPING	ON	ON

SCSI

ID	J11-12	J13-14	J15-16

0	OFF	OFF	OFF

1	OFF	OFF	ON

2	OFF	ON	OFF

3	OFF	ON	ON

4	ON	OFF	OFF

5	ON	OFF	ON

6	ON	ON	OFF

7	ON	ON	ON

JP13 (JUMPER BLOCK 3)

MOTOR SPIN

UP SEQUENCING	J1-2

DEVICE AUTO SPIN UP	OFF

SEQUENTIAL SPIN UP	ON

SYNC NEGOTIATION	J3-4

HOST ADAPTER INITIATED	OFF

TARGET INITIATED	ON

J5-6

SCSI Parity Enable/Disable

J7-8

Reserved for SCSI Function

J9-10

Reserved for SCSI Function

THIRD FLOPPY

CABLE SELECTION	J11-12

DOUBLE TWISTED CABLE	OFF

SINGLE TWISTED CABLE	ON

FLOPPY

PORT CONTROL	J13-14

3F0H-3F7H	OFF

370H-377H	ON

J15-16

Reserved

JP14 (JUMBER BLOCK 4)

DMA

TRANSFER SPEED	J1-2	J3-4

5.0 MB/SEC.	OFF	OFF

6.7 MB/SEC.	OFF	ON

8.0 MB/SEC.	ON	OFF

10.0 MB/SEC.	ON	ON

CMD

RECOVERY TIME	J5-6

150 NSEC	OFF

100 NSEC	ON

J7-8

Reserved

J9-10

Reserved

MAILBOX PORT

I/O BASE ADDRESS	J11-12	J13-14	J15-16

330H	OFF	OFF	OFF

340H	OFF	OFF	ON

310H	OFF	ON	OFF

230H	OFF	ON	ON

240H	ON	OFF	OFF

210H	ON	OFF	ON

130H	ON	ON	OFF

140H	ON	ON	ON


UltraStor 24F Card
UltraStor 24F

This is the UltraStor 24F SCSI adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base, Memory Address, and other jumper/switch configurations:

JP7

FLOPPY ENABLE/DISABLE (ON/OFF)

The rest of this SCSI interface cards' settings can be configured using the software supplied by the manufacturer.  Please consult the documentation that came with your SCSI interface card or contact the manufacturer of the SCSI interface card for further information.

Interrupt Request Line (IRQ)

Default - IRQ14

Base Memory Address

Default - C8000h


Ultrastor 34F Card Card
UltraStor 34F

This is the UltraStor 34F SCSI adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base Memory Address, and other jumper/switch configurations:

JP3 (JUMPER BLOCK 1)

MOTOR SPIN UP SEQUENCING	J1-2

DEVICE AUTO SPIN UP	OFF

SEQUENTIAL SPIN UP	ON

SYNC NEGOTIATION	J3-4

HOST ADAPTER INITIATED	OFF

TARGET INITIATED	ON

IRQ	J5-6	J7-8

10	ON	ON

11	ON	OFF

14	OFF	ON

15	OFF	OFF

J9-10	SCSI Parity Enable/Disable

BIOS

SEGMENT	J11-12	J13-14	J15-16

DISABLE	OFF	OFF	OFF

C4000-C7FFF	OFF	OFF	ON

C8000-CBFFF	OFF	ON	OFF

CC000-CFFFF	OFF	ON	ON

D0000-D3FFF	ON	OFF	OFF

D4000-D7FFF	ON	OFF	ON

D8000-DBFFF	ON	ON	OFF

DC000-DFFFF	ON	ON	ON

JP4 (JUMPER BLOCK 2)

MAILBOX PORT

I/O BASE ADDRESS	J1-2	J3-4

330H	OFF	OFF

340H	OFF	ON

230H	ON	OFF

130H	ON	ON

NUMBER OF HARD DRIVES	J5-6

2 (MAX) HD PER SYSTEM	OFF

7 (MAX) HD PER HOST ADAPTER	ON

HEAD MAPPING MODE	J7-8	J9-10

16 HEAD; 63 SECTOR MAPPING	OFF	OFF

64 HEAD; 32 SECTOR MAPPING	OFF	ON

64 HEAD; 63 SECTOR MAPPING	ON	OFF

64 HEAD; 32 SECTOR MAPPING	ON	ON

SCSI

ID	J11-12	J13-14	J15-16

0	OFF	OFF	OFF

1	OFF	OFF	ON

2	OFF	ON	OFF

3	OFF	ON	ON

4	ON	OFF	OFF

5	ON	OFF	ON

6	ON	ON	OFF

7	ON	ON	ON


Trantor Cards
Trantor

Windows 95 Adapter help currently includes the following Trantor SCSI cards:

Trantor T128

Trantor T130B


Trantor T128 Card Card
Trantor T128

This is the Trantor T128 SCSI adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base Memory Address, and other jumper/switch configurations:

SW1	Reserved

SW2	Reserved

SW3	Reserved

SW4	Reserved

BOOT ROM	SW5

Enable	ON

Disable	OFF

ZERO

WAIT STATE	SW6

Enable	ON

Disable	OFF

MEMORY

ADDRESS	SW7	SW8

CC00H	OFF	OFF

C800H	OFF	ON

DC00H	ON	OFF

D800H	ON	ON

JUMPER BLOCK JP1

IRQ	PINS 1 & 3	PINS 2 & 4	PINS 3 & 5

3	OFF	ON	OFF

5	ON	OFF	OFF

7	OFF	OFF	ON


Trantor130B Card Card
Trantor T130B

This is the Trantor T130B SCSI adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base Memory Address, and other jumper/switch configurations:

I/O

ADDRESS	SW1	SW2

350H	OFF	OFF

340H	OFF	ON

250H	ON	OFF

240H	ON	ON

BIOS ROM

ADDRESS	SW3	SW4	SW5

Disabled	OFF	OFF	OFF

CA000H	OFF	OFF	ON

CE000H	OFF	ON	OFF

DA000H	OFF	ON	ON

DE000H	ON	OFF	OFF

Reserved	ON	OFF	ON

Reserved	ON	ON	OFF

Reserved	ON	ON	ON

BOOT ROM	SW6

Enable	OFF

Disable	ON

SW7	Reserved (Should be OFF)

SW8	Reserved (Should be OFF)

JUMPER BLOCKS

ZERO

WAIT STATE	JP2

Enable	ON

Disable	OFF

JP3

IRQ	PINS 1-2	PINS 3-4	PINS 5-6

NONE	OFF	OFF	OFF

3	ON	OFF	OFF

5	OFF	ON	OFF

7	OFF	OFF	ON

Note - Jumper block jp4 is used for the led activity licht on the hard disk


CreativeLabs Cards
Creative Labs

Windows 95 Adapter help currently includes the following Creative Labs sound cards:

Sound Blaster

Sound Blaster Pro


Sound_Blaster Card
Sound Blaster

This is the Sound Blaster adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base, Memory Address, and other jumper/switch configurations:

DRQ1	DMA enable jumper.  Default is on which is DMA Channel 1

JP1	Joystick enable jumper.  Default is on which is enabled.

IRQ

J1	J2	J3	J4

2	ON	OFF	OFF	OFF

3	OFF	ON	OFF	OFF

5	OFF	OFF	ON	OFF

7	OFF	OFF	OFF	ON

I/O ADDRESS

J1	J2	J3	J4	J5	J6

210H	ON	OFF	OFF	OFF	OFF	OFF

220H	OFF	ON	OFF	OFF	OFF	OFF

230H	OFF	OFF	ON	OFF	OFF	OFF

240H	OFF	OFF	OFF	ON	OFF	OFF

250H	OFF	OFF	OFF	OFF	ON	OFF

260H	OFF	OFF	OFF	OFF	OFF	ON


Sound_Blaster_Pro Card
Sound Blaster Pro

This is the Sound Blaster Pro adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base, Memory Address, and other jumper/switch configurations:

I/O PORT ADDRESS

JP13	JP14

220-237H	ON	OFF

240-257H	OFF	ON

IRQ  (JP7)

J1	J2	J3	J4

2	ON	OFF	OFF	OFF

5	OFF	ON	OFF	OFF

7	OFF	OFF	ON	OFF

10	OFF	OFF	OFF	ON

DMA CHANNEL

JP5	JP6	JP7	DRQ0	DRQ1	DRQ2	DRQ3

0	ON	OFF	OFF	OFF	OFF	OFF	OFF

1	OFF	ON	OFF	OFF	ON	OFF	OFF

3	OFF	OFF	OFF	OFF	OFF	OFF	OFF

DMA CHANNEL

JP15	JP16	JP17	DACK0	DACK1	DACK2	DACK3

0	ON	OFF	OFF	OFF	OFF	OFF	OFF

1	OFF	ON	OFF	OFF	ON	OFF	OFF

3	OFF	OFF	OFF	OFF	OFF	OFF	OFF


Media_Vision Cards
Media Vision

Windows 95 Adapter help currently includes the following Media Vision sound cards:

Pro AudioSpectrum-16

Thunder Board


MV_Spec_16 Card
Pro AudioSpectrum-16

This is the Pro AudioSpectrum-16 adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base, Memory Address, and other jumper/switch configurations:

The MediaVision Pro Audio Spectrum 16 soundcard has two modes: Pro Audio Spectrum and Soundblaster compatability.  The settings for the Pro Audio Spectrum mode are software configurable.  The settings for the Soundblaster compatability mode are controlled by the following jumpers.

I/O ADDRESS (J10)

Pin 1	Pin 2	Pin 3	Pin 4	Pin 5	Pin 6

220H	ON	ON	OFF	OFF	OFF	OFF

230H	OFF	OFF	ON	ON	OFF	OFF

240H	OFF	OFF	OFF	OFF	ON	ON

BOARD ID (J2)

Pin 1	Pin 2	Pin 3	Pin 4	Pin 5	Pin 6

0	OFF	OFF	OFF	OFF	N/A	N/A

1	ON	ON	OFF	OFF	N/A	N/A

2	OFF	OFF	ON	ON	N/A	N/A

3	ON	ON	ON	ON	N/A	N/A

4	N/A	N/A	N/A	N/A	ON	ON

IRQ (J12)

Pin 1	Pin 2	Pin 3	Pin 4	Pin 5	Pin 6	Pin 7	Pin 8

7	ON	ON	OFF	OFF	OFF	OFF	OFF	OFF

5	OFF	OFF	ON	ON	OFF	OFF	OFF	OFF

3	OFF	OFF	OFF	OFF	ON	ON	OFF	OFF

2	OFF	OFF	OFF	OFF	OFF	OFF	ON	ON

DRQ (J11)

Pin 1	Pin 2	Pin 3

Do not Allow DMA Sharing	ON	ON	OFF

Allow DMA sharing	OFF	ON	ON


MV_Thunder Card
Thunder Board

This is the Media Vision Thunder adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base, Memory Address, and other jumper/switch configurations:

SW1

PORT ADDRESS

S1	S2	S3

$210-$21F	OFF	ON	ON

$220-$22F	ON	OFF	ON

$230-$23F	OFF	OFF	ON

$240-$24F	ON	ON	OFF

$250-$25F	OFF	ON	OFF

$260-$26F	ON	OFF	OFF

S4	FM ON/OFF

S5	JOYSTICK ON/OFF

S6	ADC ON/OFF  DO NOT SET TO OFF

IRQ (J1)

PIN 1	PIN 2	PIN 3	PIN 4

2	ON	OFF	OFF	OFF

3	OFF	ON	OFF	OFF

5	OFF	OFF	ON	OFF

7	OFF	OFF	OFF	ON


Microsoft Cards
Microsoft

Windows 95 Adapter help currently includes the following Microsoft sound cards:

Windows Sound System


WSS Card
Windows Sound System

This is the Microsoft Windows Sound System adapter shown.  Listed below are the possible Interrupt Request Line (IRQ), Base I/O Address, Base, Memory Address, and other jumper/switch configurations:

I/O ADDRESS

PIN1-2	PIN2-3	PIN3-4	PIN4-5

530	OFF	ON	OFF	ON

604	ON	OFF	ON	OFF

E80	OFF	OFF	OFF	ON

F40	OFF	ON	ON	OFF

All other settings are set by software.