; 
; $Revision:   1.7  $
; $Date:   21 Nov 1988  9:45:08  $
;
; **************************************************************************
; * Copyright (C) 1988 by Phoenix Technologies Ltd.  This program           
; * contains proprietary and confidential information.  All rights reserved 
; * except as may be permitted by prior written consent.                    
; **************************************************************************

; POST.MSG

; These messages are used for the POST error log. The format is:
; $ XX "yyy" 
; Where XX represents the error log number and yyy is the POST text. The $
; must always precede the number and be followed by a space. In addition the
; text is always delimited by quotes so embedded quotes are not permitted.

$ 102 
"Timer 0 or 2 failed during POST. The system board should be replaced."

$ 103
"The timer interrupt failed while testing timer 0 during POST. The
system board should be replaced."

$ 104 
"An unexpected interrupt has occurred while the processor was in protected
mode. The system board should be replaced."

$ 108
"Timer 2 failed during POST. The system board should be replaced."

$ 114
"The checksum calculated for an option ROM installed in the system does not
match the checksum stored in the option ROM. The failing option ROM or 
adapter card containing the option ROM should be replaced."

$ 130
"A shutdown failure has occurred during POST. The system board should
be replaced."

$ 131
"Gating of the A20 address line failed when entering or leaving protected
mode. The system board should be replaced."

$ 161
"The real time clock's bad battery flag bit is set. The battery should be 
replaced. If the problem persists, the system board should be replaced."

$ 162
"The checksum for CMOS is incorrect. If the problem occurs after
running automatic configuration, the battery should be replaced. If
the problem occurs after replacing the battery, the system board 
should be replaced."

$ 163
"The time and date in the real time clock has not been set or has been 
corrupted. When the Main Menu appears on the Phoenix Reference Diskette
select 'Feature Control' then 'Date and Time'. Enter the correct date and 
time at the prompts."

$ 164
"The amount of memory found in the system does not match the amount of memory
specified in CMOS. Automatic configuration should be run to correctly 
configure the system. If the problem persists after running automatic
configuration the system board should be replaced."

$ 165
"An adapter configured by PRD does not exist in the correct slot in the system.
Automatic configuration should be run to correctly configure the system."

$ 166
"An adapter configured by PRD does not exist in the slot specified in the
system or the adapter is not responding. Automatic configuration should 
be run to correctly configure the system. If the problem persists, the
adapter should be replaced."

$ 167
"A diskette drive has been found when CMOS information indicated there was 
none, or CMOS indicated there was a diskette drive but none was found.
Automatic configuration should be run to correct this error. If the problem
persists the system board should be replaced."

$ 168
"A Math Coprocessor has been found when CMOS information indicated there was 
none, or CMOS indicated there was a Math Coprocessor but none was found.
Automatic configuration should be run to correct this error. If the problem 
persists the system board should be replaced."

$ 201
"A read/write error has occurred in memory. The memory in the system should 
be replaced. If the problem persists, the system board should be replaced."

$ 202
"A memory parity error has occurred in memory. The memory in the system should
be replaced. If the problem persists, the system board should be replaced."

$ 203
"An address line failure has occurred in memory. The memory in the system
should be replaced. If the problem persists, the system board should
be replaced."

$ 301
"The keyboard controller has failed during POST. The keyboard should be
checked to make sure it is functioning correctly and is installed
correctly. If the problem persists, the system board should be replaced."

$ 304
"The clock line on the keyboard controller has failed during POST. The
keyboard should be checked to make sure it is functioning correctly and
is installed correctly. If the problem persists, the system board
should be replaced."

$ 306
"The data line on the keyboard controller has failed during POST. The keyboard 
should be checked to make sure it is functioning correctly and is installed
correctly. If the problem persists, the system board should be replaced."

$ 307
"A stuck key has been detected on the keyboard. The keyboard should be
checked to make sure it is functioning correctly and is installed
correctly. If the problem persists, the system board should be replaced."

$ 601
"The reset function has failed on the diskette subsystem. The diskette
controller has failed and should be replaced."

$ 602
"The seek function has failed on the diskette drive. The drive is malfunctioning
and should be replaced."

$ 901
"A parallel port failure has been detected."

$ 1101
"The serial port on the system board has failed. The system board should be
replaced or an alternate serial port used."

$ 1780
"Fixed disk drive 0 is either not ready or the recalibration function failed
during initialization. The fixed disk controller should be checked for proper
functioning. All connections should be checked."

$ 1781
"Fixed disk drive 1 is either not ready or the recalibration function failed
during initialization. The fixed disk controller should be checked for proper
functioning. All connections should be checked."

$ 1782
"The controller reset function failed during initialization. 
The fixed disk controller should be checked for proper functioning. 
All connections should be checked."

$ 1790
"The verify function has failed on fixed disk drive 0."

$ 1791
"The verify function has failed on fixed disk drive 1."

$ 2401
"The system board video controller has failed during POST. The system board
should be replaced."

$ 7000 
"The checksum for the chipset CMOS is incorrect. If the
problem occurs after running automatic configuration, the battery
should be replaced. If the problem occurs after replacing the
battery, the chipset CMOS should be replaced."

$ 7001
"An attempt to shadow the ROM BIOS in RAM failed. Running automatic 
configuration will turn the shadowing feature off and correct this
error. "

$ 7002
"The system could not be started using the values in the chipset CMOS.
Running automatic configuration will correct this problem by setting the
chipset CMOS to default values. You may also be able to correct this problem
by using the Configuration-Change menu to change the chipset CMOS values."

$ 8601
"The auxiliary device (mouse) was detected in the system but did not accept a
command. The auxiliary device should be checked for proper operation and
possibly replaced. If the problem persists, replace the system board."

$ 8602
"The auxiliary device (mouse) was detected in the system but an interface error
occurred while testing. The auxiliary device should be checked for proper
operation and possibly replaced. If the problem persists, replace
the system board."

$ 8603
"The auxiliary device (mouse) was detected in the system but a timeout occurred
while attempting to access it. The auxiliary device should be checked
for proper operation and possibly replaced. If the problem persists, replace 
the system board."