STANDARD MICROSYSTEMS CORPORATION Novell NetWare DOS ODI Workstation Driver For Ether 10/100 Fast Ethernet EISA Adapters INSTALLATION GUIDE This software is licensed by SMC for use by its customers only. Copyright (c) 1995 Standard Microsystems Corporation. All rights reserved. This installation guide describes: o How to use EZStart to copy the Novell NetWare DOS ODI workstation driver from the SuperDisk to your PC. o How to load the Novell NetWare DOS ODI driver and establish a network connection. o Information about installing multiple adapters. o Error messages. Note: For custom installations involving multiple frame types, refer to your Novell NetWare ODI Shell for DOS manual. NOTE: Ensure that the line speed (10 Mbps vs. 100 Mbps) configured for the adapter matches the speed of the hub to which it is attached. It is important to set the adapter at the correct line speed (10/100 Mbps) using the EISA Configuration Utility. Refer to pages 3-3 and A-9 in the user guide for further details. USING LANALYZER FOR WINDOWS The SMC DOS ODI client driver (SMC9232.COM) conforms to version 4.0 of the DOS ODI specification. To use any 4.0 DOS ODI driver with Lanalyzer for Windows, a file provided on your SuperDisk, RXMONSTK.COM, must be loaded before loading the driver: Example LSL RXMONSTK SMC9232 Another file provided on the SuperDisk, RXMONSTK.MSG is also required to use Lanalyzer for Windows and must reside in the same directory as RXMONSTK.COM. When using EZStart to copy files used by the DOS ODI client driver from the SuperDisk to a Destination Directory on the target client, RXMONSTK.COM and RXMONSTK.MSG are automatically copied to the same directory. COPYING THE DRIVER FILES From the EZStart Network Drivers and Documentation Selection screen, select 'Ether 10/100 DOS ODI Driver'. Then, when the Network Drivers and Documentation screen appears, select 'Copy Files' to copy all the files used by this driver from the SuperDisk to the Destination Directory recommended by EZStart, or to a different directory that you specify. SUPPLIED FILES Files provided in the Novell NetWare DOS ODI Client Directory include: o INSTALL.DOC This file. o RELEASE.DOC Provides a description of updates to the driver. o SMC9232.COM SMC9232 Novell NetWare ODI Client driver. o SMC9232.INS SMC9232 Novell NetWare ODI Client installation file. o NET.CFG Novell network configuration file for the driver. o LSL.COM Needed for Novell NetWare ODI DOS protocol stack. o SMCODI.BAT Batch file that automatically executes Client software. o RXMONSTK.COM File required to run Lanalyzer for Windows. o RXMONSTK.MSG File required to run Lanalyzer for Windows. LOADING THE DRIVER To install the driver: 1. Follow the instructions in the Novell NetWare ODI Shell for DOS manual. 2. Use any text editor to add the following lines to the workstation's AUTOEXEC.BAT file: CD \DOS_ODI (or path to DOS ODI driver files) LSL.COM (provided on the SMC SuperDisk) SMC9232.COM (provided on the SMC SuperDisk) IPXODI.COM (provided by Novell) NETX.EXE (provided by Novell) F:LOGIN CD \ INSTALLING MULTIPLE ADAPTERS If two adapters are installed in the same workstation: 1. Use any text editor to add the following lines to the NET.CFG file, located in the \DOS_ODI subdirectory on the SuperDisk Driver Disk: LINE DRIVER SMC9232 SLOT X LINK DRIVER SMC9232 SLOT X In the above lines, X is the slot number of the adapter, in hexadecimal. The first adapter should be the one with the lowest slot number. 2. Copy the NET.CFG file to the directory where the SMC9232.COM DOS ODI driver is located. ERROR MESSAGES "Could not find an SMC Ethernet adapter" The driver was unable to find an SMC Ethernet LAN adapter installed in the system. Check for adapter conflicts and retry the installation. Check that the adapter is seated properly in the adapter slot. "This Adapter must be configured in NET.CFG" This message will appear if you install two adapters in your system. In this case, you will need to add the adapter configuration for each adapter in a 'NET.CFG' file. Refer to the above information on installing multiple adapters. "Adapter hardware failure detected (initialization)" The adapter did not pass the initialization process. Check the adapter for configuration conflicts. "Adapter hardware failure detected (self-test)" The adapter did not pass the initialization self-test process due to a hardware problem. Check the adapter for configuration conflicts. "Other system RAM already occupies adapter RAM" The driver has detected that the adapter RAM conflicts with other RAM in the system. Reconfigure the adapter to use a different RAM address and retry the installation. "Other system ROM already occupies adapter RAM. " The driver has detected that the adapter RAM conflicts with ROM in the system. Reconfigure the adapter to use a different RAM address and retry the installation. "Adapter IRQ higher than 7 not valid in 8-bit slot" The IRQ number specified cannot be used if the adapter is inserted into an 8-bit slot. Select a different IRQ number. "I/O base address chosen for driver not valid (illegal boundary)" The I/O base address specified in the NET.CFG file cannot be used because it does not start on supported address start boundary. Change the setting in the NET.CFG file to a supported adapter setting. "I/O base address chosen for driver not valid (out of range)" The I/O base address specified in the NET.CFG file cannot be used because it is not within supported address range settings of the adapter. Change the setting in the NET.CFG file to a supported adapter setting. "IRQ chosen for driver does not match adapter configuration" The IRQ setting specified in the NET.CFG file cannot be used because it does not match the adapter soft-configuration or jumper setting found during initialization. Change the setting in the NET.CFG file to a supported adapter setting. "Adapter IRQ higher than 7 not valid in 8-bit slot" The IRQ setting specified in the NET.CFG file cannot be used because it is not valid for an adapter installed in an 8-bit slot. Change the setting in the NET.CFG file to a supported adapter setting. "IRQ chosen for adapter not valid (out of range)" The IRQ setting specified in the NET.CFG file cannot be used because it is not within the support IRQ settings of the adapter. Change the setting in the NET.CFG file to a supported adapter setting. "Cannot access adapter RAM properly" The adapter could read or write the adapter RAM. Verify that another adapter does not share the same memory space as the LAN adapter. "Adapter RAM base address on illegal boundary" The RAM base address setting specified in the NET.CFG file cannot be used because it does not start on supported RAM address start boundary. Change the setting in the NET.CFG file to a supported adapter setting. "RAM base address chosen for driver not valid (out of range)" The RAM base address setting specified in the NET.CFG file cannot be used because it does not start on supported RAM address start boundary. Change the setting in the NET.CFG file to a supported adapter setting. "RAM size chosen for driver not valid (out of range)" The RAM base address setting specified in the NET.CFG file cannot be used because it is not within the support RAM base address settings of the adapter. Change the setting in the NET.CFG file to a supported adapter setting. "RAM base address chosen for driver does not match adapter configuration" The RAM base address setting specified in the NET.CFG file cannot be used because it does not match the adapter soft- configuration or jumper setting found during initialization. Change the setting in the NET.CFG file to a supported adapter setting. "RAM size chosen for driver does not match adapter configuration" The RAM size setting specified in the NET.CFG file cannot be used because it does not match the adapter RAM size found during initialization. Change the setting in the NET.CFG file to a supported adapter setting. "Configuration corrupted; run software setup" The driver failed to initialize the adapter due to invalid data in configuration EEROM. Run the software setup utility and reconfigure the adapter. This commercial computer software and documentation is provided with RESTRICTED RIGHTS. Use, duplication, or disclosure by the Government is subject to restrictions set forth in subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013, or subparagraphs (c) (1) and (2) of the Commercial Computer Software -- Restricted Rights clause at FAR 52.227-19, or Alternate III of the Rights in Data -- General clause at FAR 52.227-14, as applicable. The manufacturer / subcontractor is Standard Microsystems Corporation, 80 Arkay Drive, Hauppauge, NY 11788. SMC and Standard Microsystems are registered trademarks; and Ether 10/100, EZStart, and SuperDisk are trademarks of Standard Microsystems Corporation. Other products and company names are registered trademarks or trademarks of their respective companies.