   Personal NetWare
                                                                    v2.00
      
      
      Personal NetWare* Installation Notes for Artisoft's
      NodeRunner Pro(TM) LAN Adapter
      ===================================================
         
         Location of Driver:     \DOS\EPROODI.COM
      
      
      General Installation
      --------------------
      
      The installation procedure will transfer files to a specific
      directory on the workstation and create or modify existing
      configuration files to fit your specific needs.  The installation
      utility INSTALL.EXE is located on Personal NetWare's "Installation
      + Utilities 1" disk.
      
      
      Installation Procedure
      ----------------------
      
      1  Run INSTALL.EXE from the "Installation + Utilities 1" Disk.
      
      2  The Personal NetWare Install program screen will appear.  You
         must complete each of the questions.  These options are specific
         to your needs.
         
         a  Step #1 asks you for your name, company name, and serial
            number of your copy of Personal NetWare.
         
         b  Step #2 gives you the option to load support files for MS
            Windows and tells you the disk space requirements. You will
            also have an option to change the directory where the
            Personal NetWare files will be copied. The default directory
            is C:\NWCLIENT.  You can specify another directory if you
            desire.
         
         c  Step #3 asks you to select a Primary Network Interface Card.
            From the list of drivers select "OEM Supplied Driver".
      
         d  Step #4 will ask you to insert the diskette containing the
            driver files. Insert the NodeRunner Pro diskette into
            drive A: and specify the source path for driver files as
            A:\DOS.
         
         e  Step #5 will let you specify if you want to Share This
            Computers Resources.
         
         f  Step #6 will let you specify a User Name for this computer.
         
         g  Step #7 will let you specify what Novell NetWare Servers are
            available on your network.
         
         h  Step #8 will allow you to configure Optimization / Network
            Management. Refer to your Personal NetWare Manual to decide
            what options you need.
         
         i  Step #9 is Configure Primary Interface Card. Specify the PORT
            address that was configured in NProSet for the NodeRunner
            Pro adapter. The default port address is 300. Select the
            Ethernet frame type you want to use. The default frame is
            Ethernet_802.2.
         
         j  Step #10 is to accept all of the configuration parameters. If
            everything is configured correctly then accept the
            configuration and start the installation. The Personal
            NetWare installation will now prompt you for the installation
            diskettes as needed.
         
         k  Step #11 is the final step. You will be prompted to insert
            the driver diskette for the third party software driver.
            Insert the NodeRunner Pro diskette into drive A: and
            specify the path to copy the files from as A:\DOS.
      
      Hints and Tips
      --------------
      
      1  NET.CFG Options:
      
         PORT - This is the base I/O address of the adapter.  Verify
         setting in NProSet.
      
         INT - The system IRQ for the adapter to use.  This option is
         only used as a reminder for which IRQ the board is set for.  It
         does not cause the driver to override the EEPROM contents.  The
         NodeRunner Pro adapters support IRQ's 2, 3, 4, 5, 7, 10, 11, 12.
      
      2  Be sure to add LASTDRIVE=Z to your CONFIG.SYS file for the
         network mappings to work properly.
      
      3  Below is a sample NET.CFG and STARTNET.BAT. These files are
         located in the C:\NWCLIENT directory by default.
         
         STARTNET.BAT:
         
         @ECHO OFF
         SET NWLANGUAGE=ENGLISH
         C:
         CD C:\NWCLIENT
         LH SHARE /F:10240 /L:200
         LH LSL
         LH EPROODI
         LH IPXODI
         LH SERVER
         VLM
         CD \
         C:\NWCLIENT\NET LOGIN
         
         NET.CFG:
         
         Link driver EPROODI
              PORT 300
              FRAME Ethernet_802.3
              FRAME Ethernet_802.2
              FRAME Ethernet_II
              FRAME Ethernet_SNAP
         
         Netware DOS Requester
              FIRST NETWORK DRIVE = F
              NETWARE PROTOCOL = PNW,BIND,NDS
              VLM = NMR.VLM
              VLM = WSSNMP.VLM
              VLM = WSTRAP.VLM
              VLM = WSREG.VLM
              VLM = WSASN1.VLM
              VLM = PNWTRAP.VLM
              VLM = PNWMIB.VLM
      
      
      
      *  Third-party trademarks are the property of their respective
         owners
      
      
