


Dynamite OS/2.1, 2.11     Build 8     8/24/94   Beta  Release.


This Beta release supports the following Dynamite models:




------------------------------------------------
 D501      ( TSENG W32 )
 Supported resolutions, and maximum refresh rates:
------------------------------------------------

                     256 colors
                     8 bpp

     640 by  480       1 MB               72Hz
     800 by  600       1 MB               72Hz
    1024 by  768       1 MB	          72Hz	

------------------------------------------------
 D301, D302, D201e, D601i, D602i ( TSENG W32i)
 Supported resolutions, and maximum refresh rates:
------------------------------------------------

                     256 colors
                     8 bpp                              

     640 by  480        1MB             72Hz  
     800 by  600        1MB             72Hz      
    1024 by  768        1 MB            72Hz
    1280 by 1024        2 MB            86 Interlaced


------------------------------------------------
 D601p, D602p ( TSENG W32p)
 Supported resolutions, and maximum refresh rates:
------------------------------------------------


                     256 colors
                     8 bpp                              

     640 by  480        1MB             72Hz  
     800 by  600        1MB             72Hz      
    1024 by  768        1 MB            72Hz
    1280 by 1024        2 MB            86 Interlaced
 







------------------------------------------------
D702, D902 ( TSENG W32p)
Supported resolutions, and maximum refresh rates:
------------------------------------------------

                     256 col
                     8 bpp

     640 by  480        1MB             72Hz
     800 by  600        1MB             72Hz
    1024 by  768        1 MB            72HZ
    1280 by 1024        2 MB            70Hz


* NOTE: When running the SETMODE.EXE utility, respect 
   the maximum refresh rates for your monitor, and Dynamite Model. 
   


                 INSTALLATION  INSTRUCTIONS OS/2 V2.1

NOTE:  The Installation Diskette Volume Label must be TSENG 1.  Please
note that there is a space between TSENG and 1.

1.      Close all DOS & Windows applications and command prompts.
2.      Open OS/2 SYSTEM.
3.      Open COMMAND PROMPTS.
4.      Open either OS/2 WINDOW or OS/2 FULL SCREEN.
5.      Insert Tseng Installation diskette in drive A.
6.      Type:
             A: [enter]
             PREPARE A: C: [enter]

             Where A: is the drive with the Tseng Installation diskette,
             and C: is the drive with OS/2 installed.

             Now remove the TSENG 1 Installation diskette from drive A:,
             shut down your system, reboot your computer, follow
             steps 1-5 again and continue with step 7 below.
7.      Type:
                A: [enter]
                INSTALL A: C: [enter]

        Where A: is the drive with the Tseng Installation diskette,
        and C: is the drive with OS/2 installed.

8.      From the DISPLAY DRIVER INSTALL window,
                select PRIMARY DISPLAY
                select OK.

9.      From the PRIMARY DISPLAY ADAPTER TYPE window,
                select TSENG LABORATORIES ET4000/W32/W32i/W32p 256 Colors
                select OK.




10.     From the MONITOR CONFIGURATION/SELECTION UTILITY window,
                select INSTALL USING DISPLAY ADAPTER UTILITY PROGRAM
                select OK.

11.     From the MONITOR CONFIGURATION/SELECTION UTILITY LOCATION
        window,
                type A:\SETMODE.EXE
                select OK

12.     SETMODE will prompt you to set refresh rates for 640x480
        resolution, 800x600, 1024x768, and finally for 1280x1024.
        Currently available choices are shown in parentheses.

13.     From the SELECT DISPLAY RESOLUTION window,
                select the desired resolution
                select OK.

14.     From the SOURCE DIRECTORY window,
                select INSTALL.

15.     When the drivers are completely installed, you will be prompted
        to shut down and restart the system for changes to take effect.
                 select OK.

16.     Remove the diskette from drive A.
17.     Shut down and restart.

You may also reference installation instructions in the OS/2 Version 2.1
Installation guide.

----------------------------------------------------------------------------

To change resolutions and pixel depths within the driver AFTER INSTALLATION,
take the following steps:
1.  Open OS/2 SYSTEM.
2.  Open System Setup.
3.  Open System.
4.  The currently selected resolution and color depth will be highlighted.
5.  To change it, simply click on the desired setting, close the System
    Notebook, Shut Down the system, and reboot the computer.

 

 WIN-OS2 FULL SCREEN REFRESH RATES

To set a refresh rate of 72 Hz for 640x480, 800x600 
and 70 Hz for 1024x768 for WIN-OS2 full screen 
do the following:

1. Copy VMODE.COM from the w32/w32i/w32p driver disk to your
   utilities directory.

2. Add the following commands to AUTOEXEC.BAT
     C:\UTIL\VMODE 72HZ
     C:\UTIL\VMODE 48K
     C:\UTIL\VMODE 72M
   where C:\UTIL is the name of your utilities directory
   containing VMODE.COM.

3. Shutdown and reboot.




WIN-OS2 full screen will now be capable of 72 hz refresh at
640x480 and 800x600, and 70 hz for 1024x768. Be sure your
monitor can handle the higher refresh rates.

Here is a list of VMODE commands and corresponding refresh
rates:

     COMMAND            RESOLUTION              REFRESH RATE

     VMODE 60HZ         640x480                 60 HZ
     VMODE 72HZ         640x480                 72 HZ

     VMODE 35K          800x600                 56 HZ
     VMODE 38K          800x600                 60 HZ
     VMODE 48K          800x600                 72 HZ

     VMODE 45M          1024x768                87 HZ INTERLACED
     VMODE 65M          1024x768                60 HZ
     VMODE 72M          1024x768                70 HZ



