Downloaded from the ATI BBS
May be distributed freely.

September 15, 1993

RELEASE NOTES FOR THE GRAPHICS ULTRA PRO/+

READ THIS FILE COMPLETELY BEFORE ATTEMPTING TO USE THIS PRODUCT

ATI TECHNOLOGIES INC
33 Commerce Valley Drive East
Thornhill, Ont.
CANADA. L3T 7N6

Head Office, Sales and Marketing ....... (416) 882-2600
Customer Support ....................... (416) 882-2626
FAX .................................... (416) 882-2620
ATI BBS ................................ (416) 764-9404
Compuserve ............................. GO ATITECH
     GENERAL INQUIRIES.................. 76004,3656 (Attention Corilee Fox)

Contents

1.0     Introduction
2.0     Installation
3.0     Contents of Distribution Diskette
4.0     Installation notes for Windows and AutoDesk
5.0     Reporting Problems

1.0     Introduction

This file contains last-minute updates that are not found in the user's
manual or in any addendum accompanying the display adapter.  Please read
this file before proceeding with the installation.

For Information on Running the INSTALL program please refer
to your User's manual in the Section:

            "CONFIGURING YOUR CARD", and "RUNNING THE INSTALL PROGRAM"

GENERAL INFO for NEW INSTALLATIONS:

- In order to match the card to your monitor and to your system
  configuration YOU MUST RUN "SET POWER UP CONFIGURATION"  BEFORE INSTALLING
  ANY DRIVERS
- PLEASE REFER TO "MAIN SELECTION MENU" in your User's Manual.
- After running "SET POWER UP CONFIGURATION", run Install Device Drivers
  and EXIT back to DOS.

If you experience any problems, please report them to ATI Customer Support
by fax (using the attached form in the manual) or by CompuServe.

2.0     Installation

The ATI GRAPHICS ULTRA PRO and GRAPHICS ULTRA+ video adapters represent
state of the art Personal Computer video technology.  While following IBM
VGA standards for producing VGA text and graphics, these adapters require
additional system resources to produce accelerated video capabilities.
Adapter installation, while greatly simplified through the ATI INSTALL
utility, requires a step by step methodical approach to ensure that the
adapter does not conflict with other system resources and will
provide optimized performance.

The following technical information is a basic outline of the steps required
to install an ATI GRAPHICS ULTRA PRO or GRAPHICS ULTRA+ video adapter.

1)  Upon removing the GRAPHICS ULTRA PRO/+ card from the box, record the
    serial number (found on the non-component side of the card) and the BIOS
    version (located on a label on a plug-in BIOS on the
    component side of the card) in your user manual.

    This serial number will assist Customer Support and also ensure that
    the Warranty form can be properly completed.


2)  Check the system hardware for internal modems, FAX cards or LAN cards
    which may be using addresses at COM4 (2E8) or addresses between the
    range of 2E0 to 2EF.

    Also ensure that LAN cards, scanner cards and other peripheral adapters
    are not using upper memory addresses between C000 and C7FF.

    If you have a system containing an on-board video controller,
    consult your owners manual on how to disable it.

    Check and record how much system memory is installed on the
    system motherboard.


3)  Review your CONFIG.SYS file to determine if a Memory Manager DEVICE
    driver is being loaded.
    Memory Manager device drivers, such as EMM386, QEMM and 386MAX, may
    interfere with the ATI installation software and should not be loaded
    until the ATI video adapter has been completely installed

    (For more information on ATI recommended Memory Manager
    configurations, please consult ATI Technical Note: TN069).


4)  After powering down your system, remove your old video adapter (or
    disable the on-board video controller) and plug-in the ATI GRAPHICS
    ULTRA PRO/+.

    Connect the video monitor cable and mouse cable to the ATI card
    and power-up the system.

    If the system fails to produce text on the monitor, return to Step 2
    and re-check the installed hardware for address conflicts.

    If no obvious conflicts are present, carefully remove all non-
    essential peripheral adapters (scanner, FAX/modem, audio, CD ROM cards,
    etc) to determine the nature of the conflict.

    If the system still does not boot, contact ATI Customer Support with
    the system brand and model number.


5)  Once the system has properly booted, place Disk 1 of the supplied ATI
    GRAPHICS ULTRA PRO/+ disks into the appropriate disk drive and run the
    INSTALL program.
    The INSTALL program may report that it has found the graphics card to
    be in a "new or changed configuration".  If this message appears, press
    any key to have the INSTALL program update the GRAPHICS
    ULTRA PRO/+ EEPROM.


    If the INSTALL program returns to DOS and states that it could not find
    a mach32 based video card in the system, return to Step 3 to remove any
    memory manager device driver from your CONFIG.SYS file.  If a different
    Error Message appears, carefully record the error message, follow any
    instructions listed in the message and contact ATI Customer Support if
    the problem persists.

6)  When the INSTALL program has completed loading and initialization, it
    will present the following screen:



                                ATI Technologies Inc.
 GRAPHICS ULTRA PRO               Version x.x             Copyright (c) 199x

                    ͻ
                              Main Selection Menu         
                    ͹
                     Set Power-Up Configuration           
                     Set Current Video Mode/Configuration 
                     Test Graphics Adapter                
                     Install Video Adapter Utilities      
                     Install Device Drivers               
                     Install Adapter Interface (AI)       
                    ͼ


    The "Set Power-Up Configuration" option must be run on new installations
    to inform the card of what monitor is attached and to determine what
    video card options will be enabled when the system is booted.
    Highlight the "Set Power-up Configuration" option and press Enter to
    get to the following menu:

                                ATI Technologies Inc.
 GRAPHICS ULTRA PRO               Version x.x             Copyright (c) 199x


                    ͻ
                              Main Selection Menu         
                    ͹
                     Set Power-Up Configuration           
    ͻ
                   Set  Power-Up  Configuration               
    ͹
     Monitor Type            : VGA or PS/2 Color              
     Power-Up Video Mode     : VGA (CV80)                     
     VGA ROM Configuration   : 8 bits                         
     Mouse Configuration     : Disabled                       
     Coprocessor Bus I/O     : Auto-select                    
     VGA Bus I/O             : 8 bits                         
     Memory Aperture         : Disabled                       
     VGA Zero Wait State RAM : Disabled                       
     VGA Memory Size         : 512k                           
    ͼ

    Selecting the "Monitor Type" option will produce a list of supported
    monitors.
    If your monitor is shown, select it from the list and press Enter.
    If your monitor does not appear, select the Custom option from the list.

    The Custom option will allow you to configure the vertical refresh
    rate your monitor supports for each resolution (ie: 640x480, 800x600,
    1024x768 and 1280x1024).
    It is important to review your monitor manual to determine the proper
    refresh rates to use for each resolution.  Selecting a refresh rate
    that is too high could damage your monitor.
    (For more information on Custom Monitor configurations, please consult
     ATI Technical Note: TN068).

    The "Power-Up Video Mode" option determines the DOS text and graphics
    capabilities when the card is powered-up.  Unless the AUTOEXEC.BAT file
    contains programs which can only run on an EGA, CGA or MDA video
    adapter, this option should remain set to VGA (CV80).  This will provide
    the highest level of DOS text and graphics resolution.

    The ATI GRAPHICS ULTRA PRO/+ card can use 16 BIT ROM Access to improve
    DOS Text performance.
    In some systems and/or some system configurations, however, this can
    cause unusual operational problems (booting problems, applications
    failing, Windows problems, etc).

    To ensure the most compatible video card configuration, the
    "VGA ROM Configuration" setting should be set to 8 BIT.
    This will not significantly impact on DOS performance and will not
    impact on Windows performance.

    The Mouse port on the GRAPHICS ULTRA PRO/+ can be configured to use one
    of two hardware port addresses and an IRQ value between 2 and 5.
    For most systems the mouse can be configured to use the Primary address
    and IRQ 5.

    It is important to ensure that no other devices are using the
    selected IRQ or port addresses as unusual mouse operation will result.
    If another mouse, trackball or pointing device is going to be used on
    the system, the Mouse Configuration can be left at Disabled.

    The "Coprocessor Bus I/O" selection sets the access method the card
    will use when sending or retrieving data from its low memory registers.
    For optimum performance, this setting should be configured as
    "Auto-select".

    Setting the "VGA Bus I/O" setting to "16 bits" provides optimum VGA and
    SuperVGA graphics performance.  The "8 bits" option would be used if a
    monochrome or CGA video adapter were installed in the same system with
    the Graphics Ultra Pro/+ card.

    The "Memory Aperture" feature allows for improved graphics performance
    by placing a video frame buffer in system memory address space.
    This frame buffer can only be used if unused system memory address
    space is available.

    In ISA systems, due to limitations of the system architecture,
    there must be less than 12MB of main system memory to allow the Memory
    Aperture to be enabled.
    If the memory space is not available, this feature must remain disabled.

    Enabling the "VGA Zero Wait State RAM" option will improve DOS text and
    graphics performance.
    This feature relies on compatible system bus timing and may not function
    properly on all systems.
    If DOS graphics or system operation is unstable, disable this option.

    The "VGA Memory Size" option sets the amount of graphics memory made
    available to VGA and SuperVGA applications.  ATI VGA drivers and VESA
    drivers may restrict resolution and color depth capability if not enough
    VGA Memory is allocated.

    Most mach32 drivers (ie: ACAD and Windows) override the VGA Memory
    setting to ensure that all video memory is available to the mach32 when
    running in accelerated modes.

    The default VGA Memory Size of 512k is best for most users
    UNLESS the GRAPHICS ULTRA PRO/+ has only 1MB of memory.

    GRAPHICS ULTRA PRO/+ with only 1 MB, the option of "Shared"
    should be selected.

    Once all of these options have been set, the "F10" key should be
    pressed to save the configuration.  While the INSTALL program is
    programming the EEPROM, a
    "Selected Memory Aperture configuration may conflict.." error
    message may appear.  If the system has 12MB or more system memory and
    the "Memory Aperture" feature has been disabled, ignore this message.
    If the system CMOS configuration has Video BIOS Shadowing enabled, you
    will be instructed to reboot the system once the programming of the
    EEPROM has been completed.

    If this message does not appear, proceed to Step 7, otherwise, reboot
    the system and run the INSTALL program.


7)  From the INSTALL program Main Menu, select the "Test Graphics Adapter"
    option.  Running the "Test VGA Color Modes" and the "Run Accelerator
    Diagnostics" tests will assist in determining if the
    GRAPHICS ULTRA PRO/+ is operating properly.

    Record any error messages and check the VGA ROM Access and VGA Zero
    Wait State ROM settings, in the Set Power-up Configuration Menu,
    before calling Customer Support.

8)  If the diagnostics have passed, reconfigure the memory manager device
    drivers in your CONFIG.SYS file, complete the Warranty Registration card
    and install any application specific device drivers.
    The installation is now complete.


3.0     Contents of Distribution Diskette

The following files are on the distribution diskettes. The files are
decompressed into the appropriate directories by the INSTALL utility.

Disk 1
    README              This file
    INSTALL.EXE         Main install program
    INSTALL.HLP         Help file for INSTALL.EXE
    INSTALL.VSF         Control file for INSTALL.EXE
    MONITOR.DAT         Control file for INSTALL.EXE
    SCRN_ADJ.EXE        Part of install.  Do not run.
    !ATI4400.CFG        EISA configuration file for EISA boards
    !ATI4402.CFG        EISA configuration file for EISA boards
    C-INFO.EXE          Video Technical Information Program
    LHARC.EXE           Disk archiving tool
    TEST.EXE            Video Accelerator Diagnostics Program
    UTILITY.LZH         Video Adapter Utilities archive
    WINDOWS
        WININST.EXE     Part of install.  Do not run.
        WININST.HLP     Help file for WININST.EXE
        MACH32W.LZH     Windows drivers archive
        MACHE.LZH       Windows drivers archive
        MACHS.LZH       Windows drivers archive

Disk 2
    !ATI4410.CFG        EISA configuration file for ISA boards
    !ATI4430.CFG        EISA configuration file for VLB boards
    LHARC.EXE           Disk archiving tool
    ACAD
        ACADINST.EXE    Part of install.  Do not run.
        ACADINST.HLP    Help file for ACADINST.EXE
        ULTRACAD.LZH    AutoCAD drivers archive
    GEMVP
        GMVPINST.EXE    Part of install.  Do not run.
        GMVPINST.HLP    Help file for WININST.EXE
        GMVPDRVR.LZH    GEM drivers archive
    HDIPCDOS
        AI.LZH          Application Interface archive
    LOTUS
        INST123.EXE     Part of install.  Do not run.
        INST123.HLP     Help file for WININST.EXE
        LOTUSDRV.LZH    Lotus 1-2-3 drivers archive
    PM
        PMINST.EXE      Part of install.  Do not run.
        PMINST.HLP      Help file for WININST.EXE
        PMCOMMON.LZH    OS/2 drivers archive
        PMDRVR1.LZH     OS/2 drivers archive
        PMDRVR2.LZH     OS/2 drivers archive
        VDRVRS.LZH      OS/2 drivers archive
    USTATION
        USINST.EXE      Part of install.  Do not run.
        USINST.HLP      Help file for WININST.EXE
        USDRIVER.LZH    Microstation drivers archive
    WORD
        WORDINST.EXE    Part of install.  Do not run.
        WORDINST.HLP    Help file for WININST.EXE
        WORDRVRS.LZH    Word for DOS drivers archive

Disk 3
    LHARC.EXE           Disk archiving tool
    CLIP
        CLIP.LZH        Video for Windows sample clip archive
    FONTS
        GSFONTS.LZH     Crystal Fonts archive
    VIDEO
        WINVIDS.LZH     Video for Windows drivers archive
        WINVIDW.LZH     Video for Windows drivers archive

4.0     Installation notes for Windows and AutoDesk

When you install windows drivers,  the "INSTALL DEVICE DRIVERS" option will
create a file named "MACH.WRI" on your hard disk in the windows directory you
specified.

Please read MACH.WRI after bringing up windows for the first time

GENERAL INFORMATION for those wishing to UPDATE WINDOWS DRIVERS only
- Select "INSTALL DEVICE DRIVERS" from the Main Selection Menu.
- Install Device the Drivers desired, and EXIT back to DOS.
- Run Windows SETUP and select the ATI mach32 display driver.
- Start Windows.
- ***** READ THE "MACH.WRI" file. *****

If you will be using our high resolution driver for AutoCAD 386, AutoShade
or 3D-Studio,  please note:

1)  If you have 1MB on your display adapter,  you may select any
    resolution as long as there is sufficient memory to support
    the selected display mode/refresh rate (refer to chart at the
    back of the manual).

2)  If you have 2MB on your display adapter,  you are advised to select any
    resolution having 256 colors or higher.

5.0     Reporting Problems

TECHNICAL SUPPORT

If you experience any problems, please report them to ATI Customer Support
by fax (using the attached form in the manual) or by CompuServe.

Make multiple photocopies of the form and use a separate form for each
problem being reported. Please mail or fax your completed forms to us
as soon as possible.

PROBLEM REPORT FORM

Please complete this form and return it to ATI Technologies Inc. at the
address or fax number listed below, or return via CompuServe. Make multiple
copies of this form.

Please attach C-INFO output to all problem reports submitted. Use a
separate form for each problem being reported.

ATI Technologies Inc.
33 Commerce Valley Drive East
Thornhill, Ontario
CANADA. L3T 7N6

FAX:  (416)882-2620

Product Name:  GRAPHICS ULTRA PRO
Rev. Number: 2.1
Customer Name:
CompuServe Address:
Fax Number:
Address:

My Hardware is Configured as follows:
CPU/Speed:
Hard Disk Space:
Memory:
Video Adapter (Make and Model):                 BIOS #:
Audio Adapter (Make and Model):
CD-ROM Drive (Make and Model):
Software:


Other system/software Information:


Problem description:






Impact of problem:






If you are sending any dumps, test cases or documentation associated
with this problem, list them here:




