Documentation for programs KOMPAK/CMD and KOMPAK/BAS
. 
.     The following is an explanation of the keys necessary for proper
communication with the IBM 4341 at the University Of Central Floarida.
. 
.         Keys for communication
. 
.     Because it is assumed that users of this program are familliar with
and have been in room 106 at the computer center at least once to observe
operation of a terminal communicating with the 4341 only key sequences that
are relevant to operation will be defined.
. 
.         Getting Attention After Establishing Carrier Connect.
. 
.     After establishing carrier connect use the F2 key as the 'BREAK' key
to get the attention of the communication's controller.
. 
.             Example: Press 'F2' three to four times and then press 'ENTER'
.                      If the Prompt 'ENTER CLASS' does not appear or garbage
.                      is received hang up your phone and dial back . Repeat 
.                      the 'BREAK' until prompt is received.
. 
.     Once you have received the prompt 'ENTER CLASS' type in 'IBM1' and press
'ENTER' once more.   You should receive a 'GO' at which time you will need to
press 'ENTER' once again.   You will be asked for terminal type at wich time
you will type in 'TELEVID' and press 'ENTER' again.   The UCF logo will be 
displayed and once the display is complete press 'ENTER' again.  CP READ will
appear at the bottom of your screen and from this point on only users with 
proper ID and PASSWORD will be allowed into the system.  Logon is permitted
at this point.
.
.         PF Key Sequence:
. 
.     The PF key sequence is quite simple.  For the PF key desired press the
F1 key and release it and then press 1 to = or Q to P for keys 1 to 24.  This
is a simple operation but will require that you play with them a little once
you are logged on.
. 
.         New Line Key For Xedit:
. 
.      When in Xedit the F3 key is the new line key, paging is taken care of by
the program when you reach line 15 or 16.   When using the full screen editor
be sure to move the cursor to a blank line or to the command line before 
pressing 'ENTER'
. 
.         Full Screen Editor
. 
.     The keys for the Full Screen Editor are:
. 
.         Right Arrow Moves Cursor Right One Space.
.         Left  Arrow   "     "      "    "    "
.         Up    Arrow   "     "      Up   "  Line
.         Down  Arrow   "     "     Down  "    " 
. 
.         Clear Screen And Home Cursor:
. 
.     If at any time you wish to clear the screen and home the cursor use
'SHIFT + UP ARROW',  Do not use in XEDIT except to refresh the screen if 
necessary.
. 
.        MORE....   Prompt
.  
.     At the MORE... prompt press F1 and release it and then the 'PERIOD' key
to receive the next screen.
. 
.        Dissconnect:
. 
.      If at any time you are disconnected from the system accidently do not
hang up your phone, you are still logged on.   Repeat the logon process from
the start without re-dialing and you will be re-connected.
. 
.      Hopefully the above instructions are all that is needed for you to
access the UCF system.   If you have trouble then I suggest that you become
familliar with operation of the system using a terminal in ROOM 106 of the 
computer center before trying again.   If you still have problems leave me
a message on this board and I will reply ASAP.
. 
.        Menu Keys:
. 
.      The F1 , F2, and F3 keys in the Menu Perform Exactly as Defined.
. 
.                 Michael J. Gailliot
.

       ***************** added to the ** 8/N/1 down-  ** load with the** permission of*