Help after Installation
=======================
Note: For implementation of Compuserve CIS-B Plus see its section below.
Note: If you have COMit Lite, items marked "**" are not applicable.

These instructions are available after the install by typing README
from the DOS prompt. An on-screen help system is also available AFTER
COMit is installed:

   To start COMit, type:            COMIT [Enter]
   To start help by itself, type    HELP [Enter]
   To start COMit and Help, type:   COMITH [Enter]
   ([Alt-Z] brings up "Help" if you start by using COMITH.)

If you see "Bad command or file name", change to drive and subdirectory
where COMit was installed, and try again.  For example:

 C: [Enter]    CD \COMIT [Enter]   COMIT [Enter]

If your modem did not include a printed manual, you can make one with a 
program called PRINTMAN.EXE (provided on your COMit disk.) Simply enter 
PRINTMAN or A:PRINTMAN (at the DOS prompt) for further instructions.
The INSTALL program also puts PRINTMAN.EXE on the specified destination
disk in COMit's directory if space is available.  PRINTMAN.EXE may be 
deleted when it is no longer needed.

Restoring the Init String
=========================
If you use INSTALL Type 1 (Automatic), the modem's initialization string
is automatically set up for you.  You may change the initialization string
using COMit's menu option /SI if you wish.  After a change, to restore to
the original initialization string created by INSTALL, select menu option
/SI, and choose #1.  It will be labeled "Default set by INSTALL program."

Note that some computer manufacturers and dealers pre-install COMit on your
disk.  If a different modem has been substituted after their pre-install,
you may need to use menu option /SI and select the correct modem.  In these
cases, the "Default set by INSTALL program" will not be applicable unless
you re-run INSTALL.EXE.


New Options
===========
If "S0=" is not in your initialization string, or if "S0=0" is present,
COMit will answer on the first ring.  You can change the init. string so
it contains "S0=5", for example, to make it COMit answer on the 5th ring.
COMit is also now able to auto-answer when it senses an OFF to ON change
in carrier detect.

Chat must now be enabled by pressing [C] while waiting in host mode.  If
not enabled, only the sysop on the host system can start a Chat. (**)

"Optional modem command after hangup" has been added to the Terminal Options
and Paths screen. (**)  This is an AT command to be sent after COMit hangs 
up, to reset the modem to the requirements of another program.  You can also
use it to disable auto-answering (if "S0=" was non-zero), by entering ATS0=0

In scripting, a capture file can now be opened with the "R L,filename" script
command. Use "R LD,filename" to delete the old contents of the file when it
is opened. (Otherwise, new data is appended to the capture file.)
Menu Access Key
===============
The COMit Menu Access Key is set to use [/] (FORWARD SLASH).  This brings
up a menu when using COMit or while online.  If you want to type a slash,
instead of using the menu, you can simply press [/][/].  (Press it
quickly, two times in a row.)   If, however, you wish to change the
default Menu Access Key to something else, do the following:

Go to the "SETUP" menu after starting COMit.  Select "F-Keys and Menu
Access Key."  (Option "F" on the setup menu.)

       |-|---------------------------------|
       |T|Terminal Options and Paths       |
       |-|---------------------------------|
       |H|Host Options and Paths           |
       |-|---------------------------------|
       |F|F-Keys and Menu Access Key       | <----- Select this option
       |-----------------------------------|

At the bottom of the screen, you'll see...

      |F9  [
      |F10 [
      |[/] <--- Menu access key override.  (Normally "/")
      |-------------------------------------------------------
Press enter until [/] is highlighted, then press the new key to be used.
Your override, if any, CANNOT be an [Alt] or [Ctrl] key combination or an
F-key.  We suggest one of these:  \  @  ;  ~ ` ' ] [ { } _ *

The key you select will bring up the menu when you are online. Press it
twice (quickly) to use it as a regular typing key.

Comm Ports & Internal Modems
============================
Most new computers are equipped with two serial ports. When using an
internal modem on a system that has two serial ports already installed,
you must disable one of the serial ports.  Even if you have nothing
attached to a port, it can cause a conflict with an internal modem.

If you are not sure how to disable one of the ports contact your computer
dealer. It may only require moving one or two jumpers on the card.

Compuserve B Protocol Support
=============================
COMit (** full version only) now supports Compuserve's "B" protocol for 
downloading and uploading files when connected to Compuserve. In your 
dialing directory entry for Compuserve, simply set the terminal type to 
CIS. (This is actually VT100 emulation, with Compuserve's file transfer
methods added. Note that you must press [/][B] if you want to do a scroll
back review.)

Type the file name (and optional path) when Compuserve prompts you. The
protocol is "B Plus" or "B" (if a prompt requests it.) The download or 
upload starts automatically. For downloads, crash recovery is automatic 
from the point where a previous download was interrupted if you use the 
same file names.

Using Software V.42/V.42bis
===========================
V.42 and V.42bis are implemented through COMit's software on some modems,
rather than through the modem's hardware. To use the software V.42 and 
V.42bis, simply set the MNP column of any dialing directory entry to V.42 
or V.42bis.  When you attempt to dial, COMit will notify you if the 
software V.42/V.42bis is not applicable to your modem, or if a change in 
Initialization String is necessary to use it. "Use MNP?" should be set 
to "Y" (under Host Options Setup) if software V.42/V.42bis is to be used 
in host mode.  

If you run INSTALL with Type 1 (Automatic), the Initialization String
has been already set correctly. The message to the right of the COMit logo
will indicate "V.42/V.42bis" if software MNP is available.

Many other modems implement V.42/V.42bis and/or MNP in hardware. For these,
you should set the MNP column of your dialing directory to NONE, and answer
"N" to "Use MNP" under Host Options Setup(**). Automatic INSTALL takes 
care of this.

Finally, some modems have no capability for V.42/V.42bis in hardware or
software, but MNP can be implemented in software. For these, you may set
the MNP column to MNP7, MNP5, MNP4, MNP2, REQD, or NONE. You'll be given an
error message when dialing if you set it to V.42 or V.42bis.

If your modem has hardware MNP and you want to use COMit's software MNP
instead, you must disable MNP and V.42/V.42bis on the modem by giving it
an initialization string that does so. (Consult your  modem manual for how
to do so.) 


Diagnostic Lights and Rate Reporting
====================================
A set of three "lights" replaces the rate area of the status line at
the bottom of your screen when online or when COMit is initializing the
modem or dialing.  They appear as "RxTxCd" to indicate receive, transmit,
and carrier detect.  (For modems that utilize the software V.42 driver, this
feature is unavailable during a call while the driver is active.) [Alt-R]
toggles to the "rate" indicators, then back to the "lights."

After call establishment, if the modem has reported a CARRIER rate, it will
be shown in addition to the CONNECT rate by pressing [Alt-R] again. Thus,
you can see your DTE rate (between computer and modem) and DCE rate (between
local and remote modems) while online. 

The MNP indicator on the status line now gives additional information as
well.  Lower case indications, such as mnp4, mnp5, mnp7, v42, and v42bis
indicate software MNP (or V42) is in effect.  Upper case indications,
such as MNP4, MNP5, V42, or V42BIS indicate hardware MNP or V.42 is in
effect.  The hardware indications are available only if the modem reports
them. (Depending on the modem, S95=44, W1, \V1, or other command may be
required within the initialization string.)

Forcing High Speed Modems to 2400 bps
=====================================
This feature is useful when calling information services that have 
lower prices for 2400 bps service than 9600 bps service. It can also be 
helpful when telephone line quality is bad. In the rate column of the
dialing directory, press the asterisk ("*") key, then choose a rate above 
2400 bps, such as 38400 bps. This gives the throughput benefits of a
38400 bps DTE rate, with the reliability and (sometimes) cost benefits of
a 2400 bps DCE rate. Press "*" again if you want to remove the asterisk. 
This feature is available with modems that support the AT N0 S37=6 command,
and should only be used with 9600 bps (or higher) modems.


115200 bps Support
==================
Generally, the 115200 bps rate can be used with modems that have a speed 
capability above 19200 bps. For external modems, a 16550 type (FIFO) chip 
on the serial card is recommended. 

Keyboard lock up
=================
If you are experiencing lock ups at the dialing directory in 
COMit for DOS, and are using MS DOS version 6.0 or 6.2, run
MEMMAKER, a program that came with MS DOS. (Type MEMMAKER from
the DOS prompt -- not from a Windows DOS prompt.)

Use the express setup. Respond YES when asked if you have programs 
that use expanded memory. This will usually resolve the problem.

After installations of DOS 6.0 and Windows and DOS 6.2 you may find 
SMARTDRIVE is installed in AUTOEXEC.BAT as well as in CONFIG.SYS.  
Removing the command from one of them will usually fix the lock ups 
if MEMMAKER fails to do so.

New Initialization String Option
================================
COMit normally monitors the carrier detect signal from the modem, and hangs
up the phone upon loss of carrier.  To make COMit ignore the carrier detect
signal, and instead, wait for a "NO CARRIER" message from the modem, simply
put "@" before your initialization string in COMit's Setup.  For example:
@AT&F.  (COMit does not send the "@" to the modem.)  This may help in cases
where COMit is hanging up the phone soon after a connection is established.
You can also put the "@" before the Dial prefix or a phone number.

Cellular Setup
==============
COMit now supports certain modems which have Cellular phone capabilities,
Depending on which phone cable is connected, it can distinguish a
"land line" call from a cellular call.  For cellular calls a different 
initialization string can be sent to the modem, and a slower rate can be
set automatically.  This is handled automatically by selecting the 
appropriate modem model in "Setups - Initialization String", and by
installing the "driver" software, if any, provided with the adapter to
your cellular phone.

The initialization string for cellular calls is stored at the end of the
list of modems under "Setups - Initialization String" in an entry labeled
"CEL".  You may edit it if necessary, then press [Enter].  The "Type" code 
is "None" for non-cellular modems, "Type 1" for modems which need a driver
file to be loaded each time the modem is powered-up, and "Type 2" for modems
that have the driver "permanently" stored in flash memory. Spacebar changes
the type code, as well as the maximum bps rate for cellular calls.

Your non-cellular initialization string appears at the upper right of your
dialing directory screen.  The cellular initialization string automatically
overrides it when appropriate.

Line Quality Test
=================
The "Q" option has been added to the On-Line Menu. You may also press Alt-Q
while on-line.  This sends the AT%L and AT%Q commands to the modem to get
data of interest to modem technicians. Modems not supporting this option 
display "ERROR", which can be ignored.


                             Upgrade Notice!
     *******************************************************************
     * Get Compuserve CIS-B protocol, Host Mode (BBS), VT100           *
     * and a Hard Copy Manual!   FULL Featured COMit DOS or COMit for  * 
     * Windows for only $24.95   ... or get both for $44.95            *
  *************************************************************************
  *  What the experts have to say about COMit...                          *
  *                                                                       *
  *  Best are COMit, a full-fledged communications package that could     *
  *  save you from buying anything else... PC MAGAZINE - April 27, '93    *
  *                                                                       *
  *  I've never seen an easier, faster installation. It's ready to        *
  *  go on-line minutes after coming out of the box. And its script-      *
  *  writing is a dream for beginners -- fully automated and easily       *
  *  edited.  MOBILE OFFICE - February '92                                *
  *************************************************************************
      *                                                               *
      *    Mail the following coupon with payment to ...              *
      *                                                               *
      *    Tradewind Software, P.O. Box 36, Glendora, CA 91740 USA    *
      *                                                               *
      *****************************************************************

   Yes! Send me the Full Featured version of COMit:  [  ]Dos...... $24.95
                                                     [  ]Windows.. $24.95

   Yes! Send me BOTH the DOS and Windows versions:   [  ]Both..... $44.95


 Name: ____________________________________________________________________

 Company: _________________________________________________________________

 Address:  ________________________________________________________________

 City: _______________________ State: ____________  Zip: __________________

 Phone (___) ____-____________   ===========================================
                                 | Include Shipping and Tax. Shipping is   |
                                 | $4.50 US, $5.50 Canada, $10.50 elsewhere|
 Payment Enclosed $___________   | If you live in California, tax is       |
                                 | $2.17 each or $3.19 for the Combo.      |
                                 ===========================================
 

 ( ) Visa - Master Card # ______/______/______/______ Exp Date ______/______

     Signature:  ___________________________________________________________
                             (For Visa or Master Card)


