/*
 * Project: Data Quest Program
 * Version: 1.0
 */
@DefineProject
	@Name = "QUEST"
	@Version = "1.0"
	
	@Subdir = "\\QUEST"
	@OutDrive = Z
@EndProject
@DefineVars
	@Qstring @UserName = ""
@EndVars
@GetString @UserName



				DATA QUEST

	You are installing DataQuest from Quest Inc. brought to you by
	Vance Baldwin Inc.  This program includes over 350,000 part 
	numbers from six different manufacturers with over 75,000
	substitute part numbers.


	Be sure to register your program as soon as it is installed.
	
        Be sure to select your update preference to keep your part
	numbers and prices current and accurate.


	You will want to tag your program with your company name.	

	@Prompt = " Enter your company name here "

	
@EndString
@Display
	@Cls

	This program will install:
	@Name version @Version
	on your computer system and verify the integrity of the
	distribution disk(s).  You may press the [Esc] key at any time to
	abort the installation.

	INSTALL will ask you several questions about your computer
	hardware and then give you the option of installing @Name.

	Each question has a default answer.  If the default answer is
	correct, press the ENTER key in response to the question.
	Otherwise, type the answer and then press the ENTER key.

	If you make a mistake while typing, press the BACKSPACE key
	and then retype the answer.

	@Pause
@EndDisplay
@GetOutDrive
	@Cls

	On which disk drive do you wish to install @Name?

@EndOutDrive
@GetSubdir
	@Cls
	Now you need to specify the disk destination subdirectory.  The
	subdirectory is the location on your disk where the @Name system
	will be installed.  

	@Prompt = "Which subdirectory ([Enter] = @Subdir) ?"
@EndSubdir
@Display
	@Cls
	@If (@DiskFree(@OutDrive) < 15M)
		The selected output disk drive only has
		@DiskFree(@OutDrive) bytes.  This project
		requires 15Meg. to load and run well.
		@Pause
		@Abort
	@Else
		Your disk has @DiskFree(@OutDrive) bytes.
		Your program will load fine.
		@Pause
	@Endif
@EndDisplay
@DefineDisk
	@Label = "Disk #1"
	@BeginLib PARTS.001
		@File VALL_PN.VCB @Size 9411697
	@EndLib
@EndDisk
@DefineDisk
	@Label = "Disk #2"
	@BeginLib PARTS.002
		@File VALL_PN.VCB @AppendTo VALL_PN.VCB
	@EndLib
@EndDisk
@DefineDisk
	@Label = "Disk #3"
	@BeginLib PARTS.003
		@File VALL_PN.VCB @AppendTo VALL_PN.VCB
		@File VALL_DES.VCB @Size 684630
		@File VALL_SUB.VCB @Size 274266
		@File VALL_TP.VCB @Size 2294272
	@EndLib
@EndDisk
@DefineDisk
	@Label = "Disk #4"
	@BeginLib PARTS.004
		@File VALL_TP.VCB @AppendTo VALL_TP.VCB
		@File VANC__.VCB @Size 4032
		@File VB_CL.VCB @Size 616
		@File VB_INFO.VCB @Size 953
		@File VANCE.MEM @Size 6328
		@File VANC__.FPT @Size 26815
		@File VB.BAT @Size 155
		@File VB_P.VCB @Size 940499
		@File VALL_QVB.VCB @Size 1897
	@EndLib
@EndDisk
@Finish
	@ChDrive @OutDrive
	@ChDir "@SubDir"

	Installation of @Name is now finished.
	
	To start your program type VB and enter.

	@Pause
@EndFinish
/* end-of-file */