  HOW TO INSTALL THE REMOTE OFFICE HOST WITH WINDOWS FOR WORKGROPS 3.11
  ---------------------------------------------------------------------

  WFW requires the NDIS interface into Remote Office.  Fortunately,
  WFW has a very effective setup program which can be instructed to
  modify its configuration files to accomodate Remote Office.

  The install program assumes the Windows System directory to
  be C:\WINDOWS\SYSTEM or the directory specified when choosing
  the option to install the Remote Office Windows Client.  If
  you did not install our Windows client or Windows for Workgroups
  is not installed in C:\WINDOWS\SYSTEM, skip the next section and
  follow the instructions for "WINDOWS FOR WORKGROUPS NOT INSTALLED
  BEFORE REMOTE OFFICE".


  WINDOWS FOR WORKGROUPS INSTALLED BEFORE REMOTE OFFICE

  If Windows for Workgroups was installed before Remote Office, the
  Remote Office install procedure will copy a file called "OEMROF.INF"
  to the WINDOWS SYSTEM directory.  Once the Remote Office install
  has been run, the following steps must be performed to complete
  the setup:

  1.  Load windows, from Progam Manager,
  2.  Choose the "NETWORK"  icon.
  3.  Choose the "NETWORK SETUP" icon.
  4.  Activate the "Networks" button.
  5.  Select the 2nd radio button, which installs the Windows For
      Workgroups network.
  6.  Select the "No Additional Networks" radio button and press OK.
  7.  From the Network Setup Window, activate the "Sharing" button.
  8.  Select the option to give others access to your files (if desired).
  9.  Select the "Drivers" button.
  10. Remove the current adapter setup.
  11. Choose "ADD ADAPTER".
  12. Select "Stampede Remote Office NDIS Driver".
  13. Remove MicroSoft NETBEUI protocol.
  14. Choose "ADD PROTOCOL".
  15. Select "MicroSoft NETBEUI with Remote Office Parameters".
  16. Remove "IPX/SPX Compatible Transport with NETBIOS".
  17. Continue with the network setup.
  18. See important note below.


  WINDOWS FOR WORKGROUPS NOT INSTALLED BEFORE REMOTE OFFICE

  1.  Install Windows for Workgroups.  (Select no network support).
  2.  Choose the "NETWORK"  icon.
  3.  Choose the "NETWORK SETUP" icon.
  4.  Activate the "Networks" button.
  5.  Select the 2nd radio button, which installs the Windows For
      Workgroups network.
  6.  Select the "No Additional Networks" radio button and press OK.
  7.  From the Network Setup Window, activate the "Sharing" button.
  8.  Select the option to give others access to your files (if desired).
  9.  Select the "Drivers" button.
  10. Remove the current adapter setup.
  11. Choose "ADD ADAPTER".
  12. Select "Unlisted or Updated Network Adapters".
  13. At the prompt for OEMSETUP.INF, enter your Remote Office directory.
  14. Select "Stampede Remote Office NDIS Driver" as the adpater.
  15. Remove MicroSoft NETBEUI protocol.
  16. Choose "ADD PROTOCOL".
  17. Select "MicroSoft NETBEUI with Remote Office Parameters".
  18. Remove "IPX/SPX Compatible Transport with NETBIOS".
  19. Continue with the network setup.

  IMPORTANT:
  Windows for Workgorups may insert a "NET START" line at the
  begining of the AUTOEXEC.BAT file.  If this is the case, remove
  that line.   Use the ROSTART.BAT file located in the ROFFICE
  directory.

  If you wish to load the system using an alternate BAT file, the load
  sequence should be similar to the following.

  CD\ROF
  ROFFICE
  NET INIT
  NDROF-E
  RO LOGIN HOST
  NET START NETBEUI
  WIN

