/*
 * Project: Data Quest Program
 * Version: 1.0
 */
@DefineProject	
	@Name = "DATA QUEST UPDATE"
	@Version = "1.0"
	
	@Subdir = "\\QUEST"
	@OutDrive = Z
@EndProject
@Display
	@Cls


			      DATA QUEST UPDATE 
                           -----------------------


	You are updating DataQuest from Quest Inc. brought to you by

	Vance Baldwin Inc.  This data includes over 516,990 part 

	numbers from nine different manufacturers with over 117,000

	substitute part numbers.


	@Pause
@EndDisplay	
@Display
	@Cls

	This program will install:
	@Name version @Version UPDATE DATA
	on your computer system and verify the integrity of the
	distribution disk(s).  You may press the [Esc] key at any time to
	abort the installation.

	INSTALL will ask you several questions about your computer
	hardware and then give you the option of installing @Name.

	Each question has a default answer.  If the default answer is
	correct, press the ENTER key in response to the question.
	Otherwise, type the answer and then press the ENTER key.

	If you make a mistake while typing, press the BACKSPACE key
	and then retype the answer.

	@Pause
@EndDisplay
@GetOutDrive
	@Cls

	On which disk drive do you wish to install @Name?

@EndOutDrive
@GetSubdir
	@Cls
	Now you need to specify the disk destination subdirectory.  The
	subdirectory is the location on your disk where the @Name system
	is installed.  The program must be already installed there as
	this update data will only work if the program is found.

	@Prompt = "Which subdirectory ([Enter] = @Subdir) ?"
@EndSubdir
@Display
	@Cls
	@If (@Exists("@OutDrive:\\@Subdir\\vb_p.vcb"))
		@Delete("@OutDrive:\\@Subdir\\vall_eqi.vcb")
		@Delete("@OutDrive:\\@Subdir\\vall_edi.vcb")
	@Else
		The selected output directory does not contain
		the Data Quest parts program.
		The Install will abort now.. try again.
		@Pause
		@Abort
	@Endif
@EndDisplay
@DefineDisk
	@Label = "Disk #1"
	@BeginLib PARTS.001
		@File VALL_DES.VCB @Size 980938
		@File VALL_ED.VCB @Size 153
		@File VALL_EQ.VCB @Size 406994
		@File VALL_PN.VCB @Size 13958956
	@EndLib
@EndDisk
@DefineDisk
	@Label = "Disk #2"
	@BeginLib PARTS.002
		@File VALL_PN.VCB @AppendTo VALL_PN.VCB
	@EndLib
@EndDisk
@DefineDisk
	@Label = "Disk #3"
	@BeginLib PARTS.003
		@File VALL_PN.VCB @AppendTo VALL_PN.VCB
	@EndLib
@EndDisk
@DefineDisk
	@Label = "Disk #4"
	@BeginLib PARTS.004
		@File VALL_PN.VCB @AppendTo VALL_PN.VCB
		@File VALL_QVB.VCB @Size 1896
		@File VALL_SUB.VCB @Size 231458
		@File VALL_TP.VCB @Size 3449856
	@EndLib
@EndDisk
@DefineDisk
	@Label = "Disk #5"
	@BeginLib PARTS.005
		@File VALL_TP.VCB @AppendTo VALL_TP.VCB
		@File VANCE.MEM @Size 9105
		@File VB_INFO.VCB @Size 1161
		@File VB_P.VCB @Size 812103
	@EndLib
@EndDisk
@Finish
	@ChDrive @OutDrive
	@ChDir "@SubDir"

	Installation of Data Quest Update Data is now finished.
	
	To start your program type VB and enter.

	@Pause
@EndFinish
/* end-of-file */