@DefineDisk

	@Label = "DISK 2 OF 8"	

   @If ( 'E' [= @Group )

       @BeginLib DCADBEDS.RED

           @File   *.*     @Out    \@Subdir\SYM\BEDS\*.*

       @EndLib

       @BeginLib DCADCHAI.RED

           @File   *.*     @Out    \@Subdir\SYM\CHAIRS\*.*

       @EndLib

       @BeginLib DCADCLAB.RED

           @File   *.*     @Out    \@Subdir\SYM\COLUMNS\LABELS\*.*

       @EndLib

       @BeginLib DCADCOLU.RED

           @File   *.*     @Out    \@Subdir\SYM\COLUMNS\*.*

       @EndLib

       @BeginLib DCADDESK.RED

           @File   *.*     @Out    \@Subdir\SYM\DESKS\*.*

       @EndLib

       @BeginLib DCADDRAW.RED

           @File   *.*     @Out    \@Subdir\SYM\DRAWING\*.*

       @EndLib

       @BeginLib DCADFL.RED
           
           @File   *.*     @Out    \@Subdir\SYM\FL_LIGHT\*.*

       @EndLib

       @BeginLib DCADREF.RED

           @File   *.*     @Out    \@Subdir\SYM\REFRIGER\*.*

       @EndLib

       @BeginLib DCADSIGN.RED

           @File   *.*     @Out    \@Subdir\SYM\SIGNAL\*.*

       @EndLib

       @BeginLib DCADSINK.RED

           @File   *.*     @Out    \@Subdir\SYM\SINKS\*.*

       @EndLib

       @BeginLib DCADSLAB.RED

           @File   *.*     @Out    \@Subdir\SYM\SINKS\LABELS\*.*

       @EndLib

       @BeginLib DCADTOIL.RED

           @File   *.*     @Out    \@Subdir\SYM\TOILETS\*.*

       @EndLib

       @BeginLib DCADTLAB.RED

           @File   *.*     @Out    \@Subdir\SYM\TOILETS\LABELS\*.*

       @EndLib
       
   @EndIf

   @If ( 'D' [= @Group )

       @BeginLib DCADDCX.RED
      
           @File   *.*     @out    \@Subdir\DCX\*.*

       @EndLib 

       @BeginLib DCADDWG.RED

		    @File   VELSAMP.DC5	    @Out	\@Subdir\DWG\*.*
		    @File   PLAN_1-4.DC5    @Out	\@Subdir\DEFAULT\*.*

       @EndLib

       @BeginLib DCADSUP.RED

			@File   *.*	    @Out    \@Subdir\SUP\*.*

       @EndLib

       @BeginLib FONTPOF.RED

			@File   *.*	    @Out    \@Subdir\SUP\FONTPOF\*.*

       @EndLib

       @BeginLib HATCHPOF.RED

			@File   *.*	    @Out    \@Subdir\SUP\HATCHPOF\*.*

       @EndLib

       @BeginLib LINEPOF.RED

			@File   *.*	    @Out    \@Subdir\SUP\LINEPOF\*.*

       @EndLib

   @EndIf

   @If ( 'H' [= @Group )
              
       @BeginLib DCADGIF.RED  
                
           @File   *.*     @Out    \@Subdir\HELP\*.*
        
       @EndLib

   @EndIf

@EndDisk	

@If (( 'E' [= @Group ) ||
     ( 'D' [= @Group ))

   @Chain ("DISK 3 OF 8")

@ElseIf (( 'D' [= @Group ) ||
         ( 'C' [= @Group ) ||
         ( 'P' [= @Group ) ||
         ( 'U' [= @Group ))

   @Chain ("DISK 4 OF 8")

@ElseIf (( 'D' [= @Group ) ||
         ( 'H' [= @Group ))

   @Chain ("DISK 5 OF 8")

@ElseIf ( 'E' [= @Group )

   @Chain ("DISK 6 OF 8")

@ElseIf (( 'E' [= @Group ) ||
         ( 'V' [= @Group ))

   @Chain ("DISK 7 OF 8")

@ElseIf ( 'V' [= @Group )

   @Chain ("DISK 8 OF 8")

@EndIf

@Finish

   @If ('V' [= @Group)
   	@Mkdir ("@OutDrive3:\\@Subdir3\\VTM")
   @EndIf

   @Cls

	@ChDrive@OutDrive
        @ChDir "@Subdir"


   @If ('V' [= @Group)
       @If (!(100 [= @Option))
@Rename("@OutDrive3:\\@Subdir3\\CLIPPL64.EXE","CLIPPL.EXE")
@Rename("@OutDrive3:\\@Subdir3\\RDRPL640.EXE","RDRPL.EXE")
       @Else
@Rename("@OutDrive3:\\@Subdir3\\CLIPPLEM.EXE","CLIPPL.EXE")
@Rename("@OutDrive3:\\@Subdir3\\RDRPLEMS.EXE","RDRPL.EXE")
       @EndIf

   @EndIf
   @If (('A'[=@Group) || ('D'[= @Group) || ('U'[= @Group ))
        The DataCAD Configuration Utility will now be run.  This is
        where you should select your display device, digitizer (if any),
        plotter, etc.

        @If (('A'[=@Group) || ('D'[= @Group ))
           @Mkdir ("@OutDrive:\\@Subdir\\LYR")
           @Mkdir ("@OutDrive:\\@Subdir\\PLT")
           @Mkdir ("@OutDrive:\\@Subdir\\SYM")
           @Mkdir ("@OutDrive:\\@Subdir\\TPL")
        @EndIf
	@pause
   @If (@Spawn ("CONFIG"))
   @EndIf
   @EndIf
   @Cls

        The installation has been successfully completed.
        To run DataCAD, type RUNDCAD at the DOS prompt and
        press <Enter>.

	Note:  Please be sure you have installed your mouse
	       manufacturer's supplied driver according to
	       their instructions prior to running DataCAD.

	Thank-you for choosing DataCAD!

	@pause
@EndFinish
