@DefineProject
	@Name 		= "The Amazon Trail"
	@Version	= "1.0"
	@Subdir 	= "\\MECC\\AMAZON\\"
	@Requires @HardDisk
	@OutDrive 	= c
@EndProject

@Display
	@Cls
            	      @Name Installation Program
            	      ===================================

        This program will install @Name on your computer.
	
        You may press the ESC key at any time to stop the installation.
	
        You will be asked several questions about where you want to
        install @Name on your computer.

        Each question has a suggested answer.  If our suggestions are
        okay with you (and in most cases they should be), just press
        the ENTER key when you see each question.

	@Pause
@EndDisplay


@GetOutDrive
	@Suppress A
	@Suppress B
	@Cls
	Use the arrow keys to highlight the drive to install
	@Name on and press ENTER.












@EndOutDrive


@Display
	@If (@DiskFree @OutDrive < 7500000)
	The selected output disk only has
	@DiskFree @OutDrive bytes. This product
	requires 7500000 bytes.
	@Pause
	@Abort
	@EndIf

@EndDisplay

@GetSubdir
	@Cls
        Now you need to specify the subdirectory. The
        subdirectory is the location on your disk where
        @Name will be installed.  
	
        If you don't know what a "subdirectory" is, you probably
        don't need to change it, and should press ENTER.

        If you want to change it, type the appropriate subdirectory
        and then press the ENTER key. If you make a mistake while typing, 
        press the BACKSPACE key and then retype the answer.



	@Prompt = "The default subdirectory is @Subdir. Press ENTER if this is okay."
@EndSubdir

@DefineDisk
	@Label = "DISK 1"
	@BeginLib AMAZON.LIF
		@File ALBUM.PCX @Size 53825
		@File AMAZON.EXE @Size 366912
		@File AMAZON.ICO @Size 766
		@File AMAZON.PIF @Size 545
		@File AMAZON2.RES @Size 181184
		@File BOOK.PCX @Size 38073
		@File HALL.PCX @Size 122853
		@File SETUP.BAT @Size 19
		@File SHIELD.PCX @Size 12853
		@File SHIELDMS.PCX @Size 5083
		@File SSM12_AT.GFT @Size 2612
		@File TMS21_AT.GFT @Size 3000
		@File README @Size 510
		@File AMAZON.BAT @Size 29 @out C:\AMAZON.BAT
	@EndLib
	@File     PRODUCT.PF
	@BeginLib amazon1.001
	@File amazon1.res  @Out amazon1.RES
	@EndLib
@EndDisk

@DefineDisk
	@Label = "DISK 1"
	@BeginLib amazon1.002
	@File amazon1.res @Out amazon1.RES
	@EndLib
@EndDisk

@DefineDisk
	@Label = "DISK 1"
	@BeginLib amazon1.003
	@File amazon1.res @Out amazon1.RES
	@EndLib
@EndDisk

@Finish

    @ChDrive @OutDrive		/* change to the output drive */
    @ChDir "@Subdir"		/* change to the output subdirectory */
    @Cls
    @Name Audio Setup
 

    If you have a sound and/or music card you will want to set up
    @Name to sound its best.  The next part of the installation
    will allow you to select and configure audio for your system.

    You may want to change your sound and/or music card setup
    at a later time. At the @OutDrive:@Subdir prompt type 
    SETUP and press ENTER.

    @Pause	

    @System("setup.bat")

    @Cls
    @Name installation is complete. 
    
    If you wish to start @Name right away, at the DOS prompt
    type AMAZON and press the ENTER key. 
    
    @Name places a batch file in your root directory to simplify
    starting the program at a later time. At the @OutDrive: prompt 
    type AMAZON and press ENTER.

    If you remove this batch file from your @OutDrive: directory
    you may have to use DOS commands to change your drive and/or 
    subdirectory.
    
    At the @OutDrive: prompt you would type CD @Subdir and
    press ENTER. To start @Name, type AMAZON and press ENTER.
   
    There may be a README file in the @OutDrive:@Subdir subdirectory.
    This text file will contain any last minute information that did
    not make it into the manual. To view this file type TYPE README 
    and press ENTER.

	
    @Pause	
@EndFinish
/* end-of-file */
